2005-2008 RAV4 · Service Manual TRANSMISSION

P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)

Diagnostic trouble codes · Vehicles built from Aug 2007

DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, SL3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0778
ECM checks for an open or short circuit in shift solenoid valves SL2 (1 trip detection logic)
Hybrid IC for solenoid indicates fail
  1. Open or short in shift solenoid valve SL2 circuit
  2. Shift solenoid valve SL2
  3. ECM

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. And the ECM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the circuit (Click here).

WIRING DIAGRAM

C119177E21

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)

  1. C136383E32
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    5 (SL2+) - 12 (SL2-)
    20°C (68°F)
    5.0 to 5.6 Ω
    5 (SL2+) - Body ground
    Always
    10 kΩ or higher
    12 (SL2-) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
  1. Connect the transmission wire connector.

  1. A175191E14
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B96-12 (SL2+) - B96-13 (SL2-)
    20°C (68°F)
    5.0 to 5.6 Ω
    B96-12 (SL2+) - Body ground
    Always
    10 kΩ or higher
    B96-13 (SL2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)

3. INSPECT SHIFT SOLENOID VALVE SL2
C140848E05
  1. Remove the shift solenoid valve SL2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SL2 (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)


← P0776 Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) (from Aug 2007)P0793 Intermediate Shaft Speed Sensor "A" (from Aug 2007) →