B1805/52 Short in Front Passenger Side Squib Circuit
Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007
Also covers:
- B1806/52 Open in Front Passenger Side Squib Circuit
- B1807/52 Short to GND in Front Passenger Side Squib Circuit
- B1808/52 Short to B+ in Front Passenger Side Squib Circuit
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
The front passenger side squib circuit consists of the center airbag sensor and the front passenger airbag.The circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1805/52 |
Center airbag sensor receives a line short signal 5 times in the front passenger side squib circuit during primary check. |
|
| B1806/52 |
Center airbag sensor receives an open circuit signal in the front passenger side squib circuit for 2 seconds. |
|
| B1807/52 |
Center airbag sensor receives a short to ground signal in the front passenger side squib circuit for 0.5 seconds. |
|
| B1808/52 |
Center airbag sensor receives a short to B+ signal in the front passenger side squib circuit for 0.5 seconds. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
- After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
| 1. CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB) |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the front passenger airbag.
Connect the white wire side of SST to the instrument panel wire connector E.
- CAUTION:
- Never connect a tester to the front passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting.
- SST
- 09843-18060
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1805, B1806, B1807, B1808 or 52 is not output.
- HINT:
- DTCs other than DTC B1805, B1806, B1807, B1808 or 52 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from the instrument panel wire.
Check that the instrument panel wire connectors (on the front passenger side airbag) are not damaged.
- OK:
- Lock button is not disengaged, and claw of lock is not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK INSTRUMENT PANEL WIRE |
Disconnect the connector from the center airbag sensor.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
g1-2 (P+) - Body ground
Below 1 V
g1-1 (P-) - Body ground
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
g1-2 (P+) - g1-1 (P-)
Below 1 Ω
g1-2 (P+) - Body ground
1 MΩ or higher
g1-1 (P-) - Body ground
1 MΩ or higher
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
g1-2 (P+) - g1-1 (P-)
1 MΩ or higher
|
|
||||
| NG | |
| 4. CHECK NO. 2 INSTRUMENT PANEL WIRE |
Disconnect the No. 2 instrument panel wire connector from the instrument panel wire.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
g1-2 (P+) - Body ground
Below 1 V
g1-1 (P-) - Body ground
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
g1-1 (P-) - Eg1-2
Below 1 Ω
g1-2 (P+) - Eg1-1
Below 1 Ω
g1-1 (P-) - g1-2 (P+)
1 MΩ or higher
g1-1 (P-) - Body ground
1 MΩ or higher
g1-2 (P+) - Body ground
1 MΩ or higher
|
|
||||
| OK | ||
| ||
