Driver Side Power Window does not Operate with Power Window Master Switch
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
- When the engine is running or the ignition switch is on (IG), the driver door power window regulator motor is driven by operating the power window regulator master switch. The driver door power window regulator motor has motor, regulator, and ECU functions.
- NOTICE:
- The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
- When the power window regulator motor assembly (on the driver side) is reinstalled or replaced, the power window control system must be initialized.
- After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
- Close the power window by fully pulling up the power window switch and holding it at the AUTO UP position.
- Open the power window by fully pushing down the switch.
- When the ECU determines that the driver door power window regulator motor has a malfunction, DTC B2311 is set.
- The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
- HINT:
- If the pulse sensor built into the power window regulator motor (on the driver side) malfunctions, the power window control system enters fail-safe mode. The remote UP / DOWN and AUTO UP / DOWN functions cannot be operated during fail-safe mode. (However, the power window can be closed by holding the power window switch in the AUTO UP position, and opened manually by pushing down the switch.)
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DTC |
Check for DTCs.
Connect the intelligent tester to the DLC3.
By following the tester screen display, check whether any DTCs are output.
Result Display
Proceed to
No output
A
DTC output
B
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW UP/DOWN) |
Perform the Active Test, using the intelligent tester to generate a control command, and then check the power window operation.
Power window regulator motor (Power window ECU) Item
Test Details
Diagnostic Note
Power Window
OFF / UP / DOWN (OFF)
-
- OK:
- Driver side power window operates normally.
- CAUTION:
- Be careful to avoid injuries as this test causes vehicle parts to move.
- During the Active Test, the jam protection function does not operate.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (MASTER SWITCH) |
Check the Data List for proper functioning of the power window master switch.
Power window regulator motor (Power window ECU) Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
D P/W Auto Switch
Driver side power window
AUTO switch signal / ON or OFF
ON: Driver side power window AUTO switch operates
OFF: Driver side power window AUTO switch does not operate
-
D P/W Up Switch
Driver side power window
UP switch signal / ON or OFF
ON: Driver side power window UP switch operates
OFF: Driver side power window UP switch does not operate
-
D P/W Down Switch
Driver side power window
DOWN switch signal / ON or OFF
ON: Driver side power window DOWN switch operates
OFF: Driver side power window DOWN switch does not operate
-
- OK:
- ON (switch operates) appears on screen.
|
|
||||
| NG | |
| 4. CHECK WIRE HARNESS (SWITCH INPUT POWER SUPPLY) |
![]() ![]() |
Disconnect the H2*1 or G8*2 switch connector.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
- for LHD:
Tester Connection
Specified Condition
H2-6 (B) - H2-1 (E)
10 to 14 V
- for RHD:
Tester Connection
Specified Condition
G8-6 (B) - G8-9 (E)
10 to 14 V
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR MOTOR) |
![]() ![]() |
Disconnect the H2*1 or G8*2 switch connector.
Disconnect the H4*1 or G9*2 motor connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
H2-8 (U) - H4-10 (UP)
Below 1 Ω
H2-5 (D) - H4-7 (DOWN)
Below 1 Ω
H2-4 (A) - H4-4 (AUTO)
Below 1 Ω
H2-3 (LED) - H4-5 (LED)
Below 1 Ω
- RHD:
Tester Connection
Specified Condition
G8-1 (U) - G9-10 (UP)
Below 1 Ω
G8-5 (D) - G9-7 (DOWN)
Below 1 Ω
G8-4 (A) - G9-4 (AUTO)
Below 1 Ω
G8-3 (LED) - G9-5 (LED)
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 6. INSPECT FUSE (D FR DOOR) |
Remove the D FR DOOR fuse from the instrument panel junction block.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK WIRE HARNESS (MOTOR INPUT POWER SUPPLY) |
![]() ![]() |
Disconnect the H4*1 or G9*2 motor connector.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
- for LHD:
Tester Connection
Specified Condition
H4-2 (B) - H4-1 (GND)
10 to 14 V
- for RHD:
Tester Connection
Specified Condition
G9-2 (B) - G9-1 (GND)
10 to 14 V
|
|
||||
| OK | ||
| ||



