Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
- When the engine is running or the ignition switch is on (IG) and the window lock switch of the power window regulator master switch is normal, the front passenger door power window regulator motor is driven by operating the front passenger door power window regulator switch.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK WIRE HARNESS (INPUT POWER SUPPLY) |
![]() ![]() |
Disconnect the G3*1 or H8*2 switch connector.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
G3-3 (B) - Body ground
Ignition switch on (IG)
10 to 14 V
- for RHD:
Tester Connection
Condition
Specified Condition
H8-3 (B) - Body ground
Ignition switch on (IG)
10 to 14 V
|
|
||||
| OK | |
| 2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side) |
![]() ![]() |
Remove the power window regulator switch.
Measure the resistance of the switch when the switch is operated.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 (D) - 2 (SD)
3 (B) - 4 (U)
UP
Below 1 Ω
4 (U) - 5 (SU)
1 (D) - 2 (SD)
OFF
Below 1 Ω
1 (D) - 3 (B)
4 (U) - 5 (SU)
DOWN
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK WIRE HARNESS (REGULATOR SWITCH - REGULATOR MOTOR) |


Disconnect the G3*1 or H8*2 switch connector.
Disconnect the G2*1 or H7* motor connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
G3-4 (U) - G2-2 (U)
Below 1 Ω
G3-1 (D) - G2-1 (D)
Below 1 Ω
G3-4 (U) or G2-2 (U) - Body ground
10 kΩ or higher
G3-1 (D) or G2-1 (D) - Body ground
10 kΩ or higher
- for RHD:
Tester Connection
Specified Condition
H8-4 (U) - H7-2 (U)
Below 1 Ω
H8-1 (D) - H7-1 (D)
Below 1 Ω
H8-4 (U) or H7-2 (U) - Body ground
10 kΩ or higher
H8-1 (D) or H7-1 (D) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) |
![]() ![]() ![]() ![]() |
LHD:
Remove the power window regulator motor.
Apply the battery voltage to connector terminals 1 and 2.
- NOTICE:
- Do not apply the battery voltage to any terminals except terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise
RHD:
Remove the power window regulator motor.
Apply the battery voltage to connector terminal 1 and 2.
- NOTICE:
- Do not apply the battery voltage to any terminals except terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR SWITCH) |


Disconnect the H2*1 or G8*2 switch connector.
Disconnect the G3*1 or H8*2 switch connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
H2-16 (U) - G3-5 (SU)
Below 1 Ω
H2-15 (D) - G3-2 (SD)
Below 1 Ω
H2-16 (U) or G3-5 (SU) - Body ground
10 kΩ or higher
H2-15 (D) or G3-2 (SD) - Body ground
10 kΩ or higher
- for RHD:
Tester Connection
Specified Condition
G8-12 (U) - H8-5 (SU)
Below 1 Ω
G8-13 (D) - H8-2 (SD)
Below 1 Ω
G8-12 (U) or H8-5 (SU) - Body ground
10 kΩ or higher
G8-13 (D) or H8-2 (SD) - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||




