DATA LIST / ACTIVE TEST
System information · Vehicles built from Nov 2005
| READ DATA LIST |
- HINT:
- Using the intelligent tester's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.
- NOTICE:
- In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Body / Body ECU / Data List.
Check the values by referring to the table below.
Main body ECU Item
Measurement Item / Display (Range)
Normal Condition
Diagnostic Note
IG SW
Ignition switch on (IG) / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off
-
ACC SW
Ignition switch on (ACC) / ON or OFF
ON: Ignition switch is on (ACC)
OFF: Ignition switch is off
-
St SW1
Start switch 1 / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off
-
St SW2
Start switch 2 / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off
-
Str Unlock SW
Steering lock condition / ON or OFF
ON: Steering is unlocked
OFF: Steering is locked
-
N SW / C SW
Clutch start switch (M/T) or park / neutral position switch (A/T) / ON or OFF
ON: Clutch pedal is depressed (M/T), shift lever in P or N (A/T)
OFF: Clutch pedal is released (M/T), shift lever in R or D (A/T)
-
Vehicle Spd Sig
Vehicle speed signal / STOP or RUN
STOP: Vehicle is stopped
RUN: Vehicle is running
-
E/G Cond
Engine condition / STOP or RUN
STOP: Engine is stopped
RUN: Engine is running
-
IG1 Relay Mon1
IG1 outer relay monitor / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off
-
IG2 Relay Mon1
IG2 outer relay monitor / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off
-
IG1 Relay Mon2
IG1 inner relay monitor / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off
-
IG2 Relay Mon2
IG2 inner relay monitor / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off
-
ACC Relay Mon
ACC relay monitor / ON or OFF
ON: Ignition switch is on (ACC)
OFF: Ignition switch is off
-
Ratch Circuit
Ratch circuit / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off, on (ACC) or engine is running
-
Start Req Sig
Starter request signal / ON or OFF
ON: ST relay is ON
OFF: ST relay is OFF
-
Pwr Cond
Power supply condition / ALL, ACC ON, IG1 IG2, ST ON
ALL: All relays are ON
ACC ON: ACC relay is ON
IG1: IG1 relay is ON
IG2: IG2 relay is ON
ST ON: ST relay is ON
-
St Relay Mon
Starter relay monitor / ON or OFF
ON: Starter relay is ON
OFF: Starter relay is OFF
-
#Code
Number of diagnosis codes / Min: 0, Max: 255
-
-
Stop Light SW 2
Stop light switch / ON or OFF
ON: brake pedal is depressed
OFF: brake pedal is released
-
Certification ECU Item
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
IG SW
Ignition switch / ON or OFF
ON: Ignition switch is on (IG)
OFF: Ignition switch is off
-
ACC SW
Ignition switch / ON or OFF
ON: Ignition switch is on (ACC)
OFF: Ignition switch is off
-
Key Lo-batt Wrn
Electrical key battery conditions / ON or OFF
ON: Battery has been depleted
OFF: Battery has been depleted
-
Unmatch Format
Code format / YES or NO
YES: Code format matches
NO: Code format differs
-
No response
Response / YES or NO
YES: Response
NO: No response
-
Wrong Code
ID code / YES or NO
YES: ID code matches
NO: ID code differs
-
Wrong C Code
Challenge code / YES or NO
YES: Challenge code matches
NO: Challenge code differs
-
Unmatch V-ID
Key number / YES or NO
YES: Key number matches
NO: Key number differs
-
Permit (Start)
Engine start permission by certification ECU / PERMIT or PROHIBIT
PERMIT: Engine start is permitted
PROHIBIT: Engine start is prohibited
-
Start Rqst
Starter request signal / YES or NO
YES: ID code box receives immobiliser unset signal
NO: ID code box does not receive immobiliser unset signal
-
S Code Chk
S code certification result / NG or OK
NG: S code certification result is abnormal
OK: S code certification result is normal
-
L Code Chk
L code certification result / NG or OK
NG: L code certification result is abnormal
OK: L code certification result is normal
-
| PERFORM ACTIVE TEST |
- HINT:
- Performing the Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Performing the Active Test as the first step of troubleshooting is one method of shortening diagnostic time. The Data List can be displayed during the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester ON.
Select the following menu items: Body / Body ECU / Active Test.
Perform the Active Test by referring to the table below.
| Item |
Test Details |
Diagnostic Note |
| Lighting Ind |
Indicator illumination ON/OFF |
- |
| Ind Condition |
Indicator light illumination pattern Green/Amber/No Sig |
- |
| S Lock Pwr |
Steering lock ECU power supply ON/OFF |
- |
| Item |
Test Details |
Diagnostic Note |
| Fr Transmitter |
Indoor electrical key antenna (front) ON / OFF |
- |