2005-2008 RAV4 · Service Manual BODY

Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

  1. When the AUTO UP / DOWN does not function, the power window control system may be in fail-safe mode. If the system has not been initialized after replacement of the driver door power window regulator motor, it also results in the same problem.

    NOTICE:
    1. The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
    2. When the power window regulator motor assembly (on the driver side) is reinstalled or replaced, the power window control system must be initialized.
    3. After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:
      1. Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.
      2. Open the power window by fully pushing down the switch.

    HINT:
    If the pulse sensor built into the power window regulator motor assembly (on the driver side) malfunctions, the power window control system enters fail-safe mode. The remote UP / DOWN and AUTO UP / DOWN functions cannot be operated during fail-safe mode. (However, the power window can be closed by holding the power window switch at the AUTO UP position, and opened manually by pushing down the switch.)


WIRING DIAGRAM

E124603E03

INSPECTION PROCEDURE


1. CHECK DTC
  1. Check for DTCs.

  1. Connect the intelligent tester to the DLC3.

  1. By following the tester screen display, check whether any DTCs are output.

    Result 
    Display
    Proceed to
    No output
    A
    DTC output
    B



B
PROCEED TO INSPECTION PROCEDURE RELEVANT TO OUTPUT DTC
A


2. READ VALUE USING INTELLIGENT TESTER (MASTER SWITCH)
  1. Use the Data List to check the function of the power window master switch.

    Power window regulator motor (Power window ECU) 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    D P/W Auto Switch
    Driver side power window AUTO switch signal /
    ON or OFF
    ON: Driver side power window AUTO switch operates
    OFF: Driver side power window AUTO switch does not operate
    -
    D P/W Up Switch
    Driver side power window UP switch signal /
    ON or OFF
    ON: Driver side power window UP switch operates
    OFF: Driver side power window UP switch does not operate
    -
    D P/W Down Switch
    Driver side power window DOWN switch signal /
    ON or OFF
    ON: Driver side power window DOWN switch operates
    OFF: Driver side power window DOWN switch does not operate
    -

    OK:
    ON (switch operates) appears on screen.



OK
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)
NG


3. READ VALUE USING INTELLIGENT TESTER (MASTER SWITCH)
  1. Use the Data List to check the function of the power window master switch.

    Power window regulator master switch assembly 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    D P/W Auto Switch
    Driver side power window AUTO switch signal /
    ON or OFF
    ON: Driver side power window AUTO switch operates
    OFF: Driver side power window AUTO switch does not operate
    -

    OK:
    ON (switch operates) appears on screen.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK


4. INSPECT FUSE (D FR DOOR)
  1. Remove the D FR DOOR fuse from the instrument panel junction block.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE (D FR DOOR)
OK


5. CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR MOTOR)

  1. E124617E03
    Disconnect the H2*1 or G8*2 switch connector.

  1. Disconnect the H4 or G9 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    H2-4 (A) - H4-4 (AUTO)
    Below 1 Ω
    for RHD:
    Tester Connection
    Specified Condition
    G8-4 (A) - G9-4 (AUTO)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)


← Rear Power Window RH does not Operate with Rear Power Window Switch RH (from Nov 2005)Key-off Operation Function Operates even if Operating Conditions are not Satisfied (from Nov 2005) →