2005-2008 RAV4 · Service Manual BODY

Key-off Operation Function Operates even if Operating Conditions are not Satisfied

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

  1. When the driver door has not been opened and fully closed, each door power window regulator motor can control its power window operation for approximately 45 seconds after the ignition switch is turned from on (IG) to off (the key is removed) by receiving operation permission signals from the main body ECU. However, when approximately 45 seconds have elapsed, or the driver door or front passenger side door is opened within approximately 45 seconds of the ignition switch being turned off (the key is removed), the power window regulator motor stops operating.
    During AUTO function operation, the window operation will continue until complete even if 45 seconds have passed or a door is opened.

    NOTICE:
    1. The power window control system uses a multiplex communication system (LIN). Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
    2. The power window control system prohibits the AUTO UP / DOWN function when the jam protection function malfunctions. Therefore, troubleshoot the power window control system after confirming that no diagnostic codes are displayed.


WIRING DIAGRAM

E124607E01

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester to troubleshoot the LIN communication line: Connect the intelligent tester to the vehicle, and turn the courtesy light switch on and off at 1.5 second intervals until communication between the tester and vehicle begins.


1. READ VALUE USING INTELLIGENT TESTER (LIN COMMUNICATION)
  1. Use the Data List to check the function of the power window regulator master switch.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and turn the tester ON.

    3. Select the following menu items: Body / Body ECU / Data List / Comm D-Door Mtr.

    4. Read the indication displayed on the tester.

      Main body ECU 
      Item
      Measurement Item / Display (Range)
      Status
      Communication D-Door Motor
      Connection status between power window regulator motor assembly (driver side) and main body ECU / OK or Stop
      OK: Connection
      Stop: No connection

      OK:
      OK is displayed on the intelligent tester screen.



NG
GO TO ENGINE IMMOBILISER SYSTEM (B2785)
OK


2. CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
  1. Check the power window operation function after the ignition switch is turned off.

    Result 
    Status
    Proceed to
    When power window can still be operated even after opening driver door or front passenger door within approximately 45 seconds of ignition switch being turned off
    A
    When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off
    B



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)
A


3. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY LIGHT SWITCH)
  1. Use the Data List to check the driver side door courtesy switch signal.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and turn the tester ON.

    3. Select the following menu items: Body / Body ECU / Data List / D Dor Cty SW.

    4. Read the indication displayed on the tester.

      Main body ECU 
      Item
      Measurement Item / Display (Range)
      Status
      D Door Courtesy Switch
      Driver side door courtesy switch signal /
      ON or OFF
      ON: Driver door open
      OFF: Driver door closed
      P Door Courtesy Switch
      Front passenger side door courtesy switch signal / ON or OFF
      ON: Front passenger door open
      OFF: Front passenger door closed

      OK:
      OK is displayed on the intelligent tester screen.



OK
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
NG


4. INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

  1. B058556E13
    Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Switch body
    Pushed
    10 kΩ or higher
    1 - Switch body
    Not pushed
    Below 1 Ω



NG
REPLACE DOOR COURTESY LIGHT SWITCH ASSEMBLY
OK


5. CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)

  1. E124650E01
    Measure the voltage without removing the IA junction block connector.

    Standard voltage:
    for Driver side (LHD):
    Tester Connection
    Driver Door Condition
    Specified Condition
    IA-21 (DCTY) - Body ground
    Fully closed
    10 to 14 V
    IA-21 (DCTY) - Body ground
    Open
    Below 1 V
    for Driver side (RHD):
    Tester Connection
    Driver Door Condition
    Specified Condition
    IC-6 (DCTY) - Body ground
    Fully closed
    10 to 14 V
    IC-6 (DCTY) - Body ground
    Open
    Below 1 V
    for Passenger side (LHD):
    Tester Connection
    Driver Door Condition
    Specified Condition
    IC-14 (PCTY) - Body ground
    Fully closed
    10 to 14 V
    IC-14 (PCTY) - Body ground
    Open
    Below 1 V
    for Passenger side (RHD):
    Tester Connection
    Driver Door Condition
    Specified Condition
    IA-24 (PCTY) - Body ground
    Fully closed
    10 to 14 V
    IA-24 (PCTY) - Body ground
    Open
    Below 1 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)


← Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch (from Nov 2005)Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated) (from Nov 2005) →