2005-2008 RAV4 · Service Manual ENGINE

Engine does not Start

Circuit diagnosis · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION


ENGINE START SYSTEM OPERATION
  1. When the engine switch is pressed with the clutch pedal depressed, the main body ECU determines that it is an engine start request.

  2. The certification ECU and other ECUs perform key verification via the LIN communication line.

  3. The main body ECU activates the ACC relay.

  4. The main body ECU activates the IG1 and IG2 relays. The engine switch indicator light illuminates in green.

  5. The certification ECU outputs a steering UNLOCK signal. The signal is sent to the steering lock ECU via the main body ECU.

  6. The main body ECU sends an engine start request signal to the ECM.

  7. The ECM sends an ACC cut request signal to the main body ECU.

  8. The ECM and main body ECU activate the ST cut relay.

  9. The main body ECU deactivates the ACC relay until the ECU detects an engine start.

  10. The ECU reactivates the ACC relay and turns off the engine switch indicator light.

    Symbols of main body ECU
    Signals
    SSW1/SSW2
    Ignition switch on (ACC, IG) signal
    ACCD
    ACC relay operation signal
    IG2D
    IG2 relay operation signal
    STR2
    ST cut relay operation signal
    STR
    Clutch start switch signal
    TACH
    Engine start detection signal
    STSW
    Starter activation request signal
    ACCR
    ACC cut request signal

B127997E03

WIRING DIAGRAM

See CRANKING HOLDING FUNCTION CIRCUIT (Click here).

INSPECTION PROCEDURE


1. CHECK WHETHER ENGINE STARTS AFTER STEERING LOCK INITIALIZATION
  1. Open and close the driver door when the ignition switch is off.

  1. Check that the engine starts.

    OK:
    Engine starts.

HINT:
After the battery runs out, the engine may not start if the steering lock ECU has not been initialized (lock / unlock may not be recorded) through the procedure described above.



OK
SYSTEM OK
NG


2. CHECK WHETHER DTC OUTPUT RECURS
  1. Clear the DTCs.

    HINT:
    After all DTCs are cleared, check if the trouble occurs again 5 seconds after the ignition switch is turned on (IG).

  1. Check for DTCs again.

    OK:
    No DTC is output.



NG
GO TO DTC CHART
OK


3. CHECK SWITCH CONDITION
  1. Ensure the electrical key is inside the cabin.

  1. Check that the power source mode changes as shown below each time the ignition switch is pushed.

OK:
off → on (ACC) → on (IG) → off



NG
GO TO POWER SOURCE MODE DOES NOT CHANGE
OK


4. CHECK BASIC FUNCTION
  1. Ensure there is fuel in the fuel tank and the key is inside the cabin.

  1. Depress the clutch pedal, and keep depressing the pedal.

  1. Check that the engine cranks when the engine switch is pressed.

OK:
Engine cranks.



OK
Go to step 8
NG


5. READ VALUE USING INTELLIGENT TESTER (CLUTCH START SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Main Body ECU / Data List / N SW / C SW.

  1. Read the displays on the tester.

    Main body ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    N SW / C SW
    Clutch switch / ON or OFF
    ON: Clutch pedal depressed
    OFF: Clutch pedal released
    -

    OK:
    When the clutch pedal is depressed, ON is displayed on the tester.



NG
REPAIR OR REPLACE CLUTCH START SWITCH
OK


6. CHECK STEERING LOCK SYSTEM
  1. When the ignition switch is on (ACC), check that the steering lock can be released.

    OK:
    Steering lock can be released.



NG
GO TO STEERING LOCK SYSTEM
OK


7. INSPECT MAIN BODY ECU

  1. A122230E03
    Disconnect the E20 main body ECU connector.

  1. Depress the clutch pedal, and keep depressing the pedal.

  1. Measure the voltage of the wire harness side connector when the engine cranks by pressing the engine switch.

    Standard voltage:
    Tester Connection
    Specified Condition
    E20-4 (STSW) - Body ground
    10 to 14 V



NG
GO TO ECD SYSTEM (CRANKING HOLDING FUNCTION CIRCUIT)
OK

REPLACE MAIN BODY ECU

8. READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
  1. Place the electrical key inside the vehicle.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Certification ECU / Data List / L Code Chk.

  1. Read the display on the tester.

    Certification ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    L Code Chk
    L Code Check / NG or OK
    NG: L code certification result is abnormal
    OK: L code certification result is normal
    -

    OK:
    L code check results is OK.



NG
GO TO ENGINE IMMOBILISER SYSTEM (STEERING LOCK ECU OR ID CODE BOX MALFUNCTIONS)
OK


9. READ VALUE USING INTELLIGENT TESTER (S CODE CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Certification ECU / Data List / S Code Chk.

  1. Read the display on the tester.

    Certification ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    S Code Chk
    S Code Check / NG or OK
    NG: S code certification result is abnormal
    OK: S code certification result is normal
    -

    OK:
    S code check result is OK.



NG
GO TO ENGINE IMMOBILISER SYSTEM (CERTIFICATION ECU OR ID CODE BOX MALFUNCTIONS)
OK


10. READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) (do not start the engine) and turn the tester ON .

  1. Select the following menu items: Body / Certification ECU / Data List / Start Req Sig.

  1. Read the displays on the tester.

    Certification ECU:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Start Req Sig
    Starter request signal / Yes or No
    Yes: ID code box receives immobiliser unset signal
    No: ID code box does not receive immobiliser unset signal
    -

    OK:
    When ID code box receives immobiliser unset signal, YES is displayed on the tester.



NO
REPLACE CERTIFICATION ECU
YES

REPLACE ID CODE BOX


← Power Source Mode does not Change (from Nov 2005)Engine does not Start (Jan 2007 – Jul 2007) →