2005-2008 RAV4 · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2008

Versions by build date: Aug 2007 – Jul 2008 from Aug 2008


1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. The "DISCHARGE FUEL SYSTEM PRESSURE" procedures must be performed before disconnecting any part of the fuel system.
  2. After performing the "DISCHARGE FUEL SYSTEM PRESSURE" procedures, pressure will remain in the fuel lines. When disconnecting a fuel line, cover it with a shop rag or a piece of cloth to prevent fuel from spraying or coming out.

  1. A128750E01
    Remove the console box (Click here).

  1. Start the engine. After the engine has stopped, turn the ignition switch off.

    HINT:
    DTC P0171/P0172 (system too lean) may be set.

  1. Check that the engine does not start.

  1. Remove the fuel tank cap, and let the air out of the fuel tank.

  1. A128750E01
    Connect the connector.

  1. Install the console box (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


3. REMOVE FUEL TANK CAP

4. DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

  1. A131635
    Remove the 2 bolts and disconnect the parking brake cable.


5. REMOVE NO. 1 FUEL TANK PROTECTOR
  1. Remove the 2 clips and grommet.

  1. Remove the 2 bolts and fuel tank protector.


6. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

  1. A124661E01
    Pinch and pull the main tube connector to disconnect the connector from the pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

  1. Disconnect the purge line hose from the pipe.


7. REMOVE FUEL HOSE PROTECTOR

  1. A199132
    Detach the claw and remove the fuel hose protector from the filler pipe hose.


8. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

A173328
  1. Disconnect the filler pipe hose from the fuel tank.


9. DISCONNECT FUEL TANK BREATHER HOSE

  1. A131627
    Disconnect the breather hose from the fuel tank.


10. DISCONNECT AIR INLET LINE HOSE

  1. A173329
    Remove the air inlet line hose.


11. REMOVE FUEL TANK FILLER PIPE
  1. Remove the 3 bolts and filler pipe protector.

  1. Remove the 2 bolts and filler pipe.


12. REMOVE FUEL TANK ASSEMBLY
  1. Set a transmission jack underneath the fuel tank.

  1. A124665
    Remove the 6 bolts and 3 fuel tank bands.

  1. Slightly lower the transmission jack.

    NOTICE:
    Be careful not to cut the wiring.

  1. A173331E01
    Fold back approximately half of any cushion rubber necessary for the detachment of the wire harness from the fuel tank in the step below.

  1. Disconnect the fuel pump connector and sender gauge connector.

    NOTICE:
    1. Before this procedure, check the connector for dirt, mud or other contamination.
    2. Do not use any tools in this procedure.

  1. Detach the wire harness from the 4 clamps and remove the fuel tank.

← REMOVAL (Aug 2007 – Jul 2008)DISASSEMBLY (from Aug 2008) →