2005-2008 RAV4 · Service Manual ENGINE

P0365 Camshaft Position Sensor "B" Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built from Aug 2007

Also covers:

DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor consists of a magnet and MRE (Magnet Resistance Element).
The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference.
When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P0365
P0390
  1. Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more seconds have elapsed after turning engine switch on (IG)
    (1 trip detection logic)
  2. No VVT sensor signal to ECM during cranking
    (1 trip detection logic)
  1. Open or short in VVT sensor for exhaust camshaft circuit
  2. VVT sensor for exhaust camshaft
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM
P0367
P0392
Output voltage of VVT sensor is 0.3 V or less for 5 seconds
(1 trip detection logic)
  1. Open or short in VVT sensor for exhaust camshaft circuit
  2. VVT sensor for exhaust camshaft
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM
P0368
P0393
Output voltage of VVT sensor is 4.7 V or more for 5 seconds
(1 trip detection logic)
  1. Open or short in VVT sensor for exhaust camshaft circuit
  2. VVT sensor for exhaust camshaft
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM

  1. A140642E02
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveform is as shown.
    2. EV1+ and EV2+ stand for the VVT sensor signal, and NE+ stands for the CKP sensor signal.
      Item
      Content
      Terminal
      NE+ - NE-
      EV1+ - EV1-
      EV2+ - EV2-
      Equipment Setting
      5 V/DIV.
      20 ms./DIV.
      Condition
      Cranking or idling


WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1. CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)

  1. A107149E80
    Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    VC2 (3) - Body ground
    4.5 to 5.0 V

  1. Reconnect the VVT sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

  1. A135027E21
    Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Specified Condition
    EX+ (B88-1) - EV1+ (B96-68)
    Below 1 Ω
    EX- (B88-2) - EV1- (B96-91)
    Below 1 Ω
    Bank 2:
    Tester Connection
    Specified Condition
    EX+ (B74-1) - EV2+ (B96-66)
    Below 1 Ω
    EX- (B74-2) - EV2- (B96-89)
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Specified Condition
    EX+ (B88-1) or EV1+ (B96-68) - Body ground
    10 kΩ or higher
    EX- (B88-2) or EV1- (B96-91) - Body ground
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Specified Condition
    EX+ (B74-1) or EV2+ (B96-66) - Body ground
    10 kΩ or higher
    EX- (B74-2) or EV2- (B96-89) - Body ground
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK VVT SENSOR FOR EXHAUST CAMSHAFT (SENSOR INSTALLATION)

  1. BR03795E18
    Check the VVT sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE VVT SENSOR
OK


4. CHECK EXHAUST CAMSHAFT
  1. Check the teeth of the camshaft.



NG
REPLACE EXHAUST CAMSHAFT
OK


5. REPLACE VVT SENSOR

NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0365, P0352, P0353, P0354, P0355 or P0356
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (from Aug 2007)P0420 Catalyst System Efficiency Below Threshold (Bank 1) (+ P0430) (from Aug 2007) →