B1860/64 Short in Driver Side Knee Airbag Squib Circuit
Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007
Also covers:
- B1861/64 Open in Driver Side Knee Airbag Squib Circuit
- B1862/64 Short to GND in Driver Side Knee Airbag Squib Circuit
- B1863/64 Short to B+ in Driver Side Knee Airbag Squib Circuit
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
The driver side knee airbag squib circuit consists of the center airbag sensor and the driver side knee airbag.This circuit signals the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side knee airbag squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1860/64 |
Center airbag sensor detects line short signal 5 times in driver side knee airbag squib circuit during primary check. |
|
| B1861/64 |
Center airbag sensor detects open signal in driver side knee airbag squib circuit for 2 seconds. |
|
| B1862/64 |
Center airbag sensor detects short to ground signal in knee airbag (D side) squib circuit for 0.5 seconds. |
|
| B1863/64 |
Center airbag sensor detects short to B+ signal in knee airbag (D side) squib circuit for 0.5 seconds. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
- After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
| 1. CHECK DRIVER SIDE KNEE AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB) |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the driver side knee airbag.
Connect the white wire side of SST to the floor wire.
- CAUTION:
- Never connect a tester to the driver side knee airbag (drive side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting.
- SST
- 09843-18060
Connect the white wire side of SST to the floor wire connector C.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1860, B1861, B1862, B1863 and 64 are not output.
- HINT:
- DTCs other than DTC B1860, B1861, B1862, B1863 and 64 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the instrument panel wire connector (on the driver side knee airbag side) is not damaged.
- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG SQUIB CIRCUIT) |
![]() ![]() |
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
E39-1 (DK+) - Body ground
Below 1 V
E39-2 (DK-) - Body ground
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E39-1 (DK+) - E39-2 (DK-)
Below 1 Ω
E39-1 (DK+) - Body ground
1 MΩ or higher
E39-2 (DK-) - Body ground
1 MΩ or higher
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E39-1 (DK+) - E39-2 (DK-)
1 MΩ or higher
|
|
||||
| OK | ||
| ||

