2005-2008 RAV4 · Service Manual BRAKE

C1243/43 Acceleration Sensor Stuck Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

This sensor detects vehicle deceleration. The sensor signal is used in ABS control. If the sensor functions abnormally, the ABS warning light turns ON.
DTC C1279/79 can be deleted when the deceleration sensor sends a deceleration sensor signal or the test mode ends. DTC C1279/79 is output only in the test mode.
DTC No.
DTC Detection Condition
Trouble Area
C1243/43
While vehicle speed decreases from 30 km/h (18 mph) to 0 km/h (0 mph), condition that ECU terminal GL1 value does not change to 0.0294 G or more occurs 16 times consecutively.
  1. Deceleration sensor
  2. Deceleration sensor circuit
  3. Brake actuator
C1244/44
When one of following conditions is met:
  1. ECU terminal GL1 value of -1.5 G or less or 1.5 G or more continues for 1.2 seconds or more.
  2. Deceleration sensor terminal VGS voltage of 4.4 V or less or 5.6 V or more continues for 1.2 seconds or more.
  3. Deceleration sensor signal momentary open occurs 7 times or more.
  1. Deceleration sensor
  2. Deceleration sensor circuit
  3. Brake actuator
C1245/45
At vehicle speed of 30 km/h (18 mph) or more, difference between back and forth G value calculated using G sensor signals and back and forth G value calculated using vehicle speed, exceeds 0.35 G for 60 seconds or more.
  1. Deceleration sensor
  2. Deceleration sensor circuit
  3. Brake actuator
C1279/79
Detected only during test mode
  1. Deceleration sensor
  2. Sensor installation

WIRING DIAGRAM

C133803E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (DECELERATION SENSOR)
  1. Check the Data List for proper functioning of the deceleration sensor.

    Skid control ECU 
    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Deceleration Sensor
    Deceleration sensor reading / Min.: -1.869 G, Max.: 1.869 G
    Approx. 0 +-0.13 G when vehicle is not moving
    Reading changes when vehicle is shaken

    OK:
    Deceleration value changes.



OK
REPLACE BRAKE ACTUATOR ASSEMBLY
NG


2. INSPECT DECELERATION SENSOR

  1. C108887E01
    Remove the deceleration sensor.

  1. Connect 3 dry cell batteries of 1.5 V in series.

    HINT:
    Do not apply 6 V or more to terminals 3 (VGS) and 2 (GGND).

  1. Check the output voltage of terminal 1 (GL1) when the sensor is tilted forward and rearward.

    Standard voltage:
    Tester Connection
    Sensor Position
    Specified Condition
    1 (GL1) - Battery's negative (-) lead
    Horizontal
    Approx. 2.3 V
    1 (GL1) - Battery's negative (-) lead
    Tilted forward
    Approx. 0.4 to 2.3 V
    1 (GL1) - Battery's negative (-) lead
    Tilted rearward
    Approx. 2.3 to 4 V

    HINT:
    1. If the sensor is tilted too much, it may output the wrong value.
    2. If the voltage drops, the sensor should be replaced with a new one.
    3. When replacing the sensor, it should not be placed upside down.



NG
REPLACE DECELERATION SENSOR
OK


3. CHECK WIRE HARNESS (SKID CONTROL ECU - DECELERATION SENSOR)

  1. C108888E03
    Disconnect the A27 ECU connector.

  1. Disconnect the K7 sensor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A27-4 (GL1) - K7-1 (GL1)
    Below 1 Ω
    A27-7 (GGND) - K7-2 (GGND)
    Below 1 Ω
    A27-28 (VGS) - K7-3 (VGS)
    Below 1 Ω
    K7-1 (GL1) - Body ground
    10 kΩ or higher
    K7-2 (GGND) - Body ground
    10 kΩ or higher
    K7-3 (VGS) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. CHECK FOR DTC
  1. Install the deceleration sensor to the vehicle.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at 6 km/h (4 mph) or more.

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← C1243/43 Acceleration Sensor Stuck Malfunction (+ C1244/44, C1245/45, C1279/79) (Jan 2007 – Jul 2007)C1249/49 Open in Stop Light Switch Circuit (Nov 2005 – Dec 2006) →