2005-2008 RAV4 · Service Manual ENGINE

P1550 Battery Current Sensor Circuit

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

A110645E01
The battery current sensor installed on the positive (+) battery terminal detects the amount of current supplied from the generator.
The battery current sensor changes current to voltage (at the positive (+) battery terminal) and sends it to the ECM. The ECM controls the voltage of the generator based on the signals from the battery current sensor.
DTC No.
DTC Detection Condition
Trouble Area
P1550
The following condition continues for 10 seconds or more with the ignition switch on (IG)
(1 trip detection logic):
  1. Difference between the maximum and minimum current values of the battery current sensor is 1 A or less
  1. Open or short in battery current sensor circuit
  2. Battery current sensor assembly
  3. ECM
P1551
Battery current sensor output value is 0.2 V or less for 0.5 seconds or more with the ignition switch on (IG)
(1 trip detection logic):
  1. Short in battery current sensor circuit
  2. Battery current sensor assembly
  3. ECM
P1552
Battery current sensor output value is 4.8 V or more for 0.5 seconds or more with the ignition switch on (IG)
(1 trip detection logic):
  1. Open in battery current sensor circuit
  2. Battery current sensor assembly
  3. ECM

WIRING DIAGRAM

A127777E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT BATTERY CURRENT SENSOR ASSEMBLY
A124656E02
  1. Disconnect the B31 battery current sensor connector.

  1. Measure the resistance of the battery current sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    VC5 (2) - E2 (4)
    3 to 10 kΩ
    VC5 (2) - IB (3)
    Below 0.5 kΩ
    IB (3) - E2 (4)
    3 to 10 kΩ



NG
REPLACE BATTERY CURRENT SENSOR ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR - ECM)
A127962E02
  1. Disconnect the B31 battery current sensor connector.

  1. Disconnect the B32 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    IB (B31-3) - IB (B32-68)
    Below 1 Ω
    VC5 (B31-2) - VCIB (B32-69)
    Below 1 Ω
    E2 (B31-4) - EIB (B32-92)
    Below 1 Ω
    THB (B31-1) - THB (B32-120)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    IB (B31-3) or IB (B32-68) - Body ground
    10 kΩ or higher
    VC5 (B31-2) or VCIB (B32-69) - Body ground
    10 kΩ or higher
    THB (B31-1) or THB (B32-120) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0724 Brake Switch "B" Circuit High (from Jan 2007)P1550 Battery Current Sensor Circuit (+ P1551, P1552) (from Jan 2007) →