2005-2008 RAV4 · Service Manual ENGINE

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling when brakes are suddenly applied while driving in lock-up condition. When the brake pedal is depressed, this switch sends a signals to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC No.
DTC Detection Condition
Trouble Area
P0724
Stop light switch remains ON even when vehicle repeats 5 cycles of STOP (less than 1.86 mph [3 km/h]) and GO (18.65 mph [30 km/h] or more)
(2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

WIRING DIAGRAM

A127780E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Read the values displayed on the tester.


OK:
Item
Measurement Item / Range (display)
Normal Condition
Stop Light Switch
Stop light switch status:
ON or OFF
  1. ON: Brake Pedal is depressed
  2. OFF: Brake Pedal is released



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
A115657E04
  1. Remove the stop light switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)

  1. A107923E03
    Disconnect the A12 ECM connector.

  1. Disconnect the A5 stop light switch connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    STP (A12-36) - Stop light switch (A5-1)
    Below 1 Ω
    ST1- (A12-35) - Stop light switch (A5-4)

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    STP (A12-36) or Stop light switch (A5-1) - Body ground
    10 kΩ or higher
    ST1- (A12-35) or Stop light switch (A5-4) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the stop light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0724 Brake Switch "B" Circuit High (Nov 2005 – Dec 2006)P1550 Battery Current Sensor Circuit (+ P1551, P1552) (Nov 2005 – Dec 2006) →