2005-2008 RAV4 · Service Manual ENGINE

P1550 Battery Current Sensor Circuit

Diagnostic trouble codes · Vehicles built from Aug 2007

Also covers:

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The battery current sensor installed on the negative battery terminal detects the amount of current supplied from the alternator.
A110645E01
The battery current sensor changes current to voltage and outputs that voltage. The battery current sensor changes current at the negative battery terminal to voltage and sends it to the ECM. The ECM controls the voltage of the alternator based on the signals from the battery current sensor.
DTC No.
DTC Detection Condition
Trouble Area
P1550
The following condition continues for 10 seconds or more with the ignition switch on (IG)
(1 trip detection logic):
  1. Difference between the maximum and minimum current values of the battery current sensor is 1 A or less
  1. Battery current sensor
  2. Wire harness or connector
  3. ECM
P1551
Battery current sensor output value is 0.2 V or less for 0.55 seconds or more with the ignition switch on (IG)
(1 trip detection logic)
  1. Battery current sensor
  2. Wire harness or connector
  3. ECM
P1552
Battery current sensor output value is 4.8 V or more for 0.55 seconds or more with the ignition switch on (IG)
(1 trip detection logic)
  1. Battery current sensor
  2. Wire harness or connector
  3. ECM

WIRING DIAGRAM

Refer to DTC P0516 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.


1. INSPECT BATTERY CURRENT SENSOR ASSEMBLY

  1. C129062E04
    Disconnect the battery current sensor connector.

  1. Measure the resistance of the battery current sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    B31-2 (VC5) - B31-4 (E2)
    3 to 10 kΩ
    B31-3 (IB)- B31-4 (E2)
    3 to 10 kΩ
    B31-2 (VC5) - B31-3 (IB)
    Below 0.5 kΩ

    HINT:
    The resistance differs according to the tester type.

  1. Reconnect the battery current sensor connector.



NG
REPLACE BATTERY CURRENT SENSOR ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR - ECM)

  1. A131549E05
    Disconnect the battery current sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B31-2 (VC5) - B32-70 (VCIB)
    Below 1 Ω
    B31-3 (IB)- B32-116 (IB)
    Below 1 Ω
    B31-4 (E2) - B32-93 (E1B)
    Below 1 Ω
    B31-2 (VC5) or B32-70 (VCIB) - Body ground
    10 kΩ or higher
    B31-3 (IB) or B32-116 (IB) - Body ground
    10 kΩ or higher

  1. Reconnect the battery current sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P1550 Battery Current Sensor Circuit (+ P1551, P1552) (Jan 2007 – Jul 2007)P1601 EEPROM Error - Injector Correction Value, DPF Thermal Degradation Record (Jan 2007 – Jul 2007) →