REMOVAL
Removal / installation · Vehicles built from Jan 2007
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 2. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() ![]() |
Using a screwdriver, detach the 4 clips, 6 claws and remove the instrument cluster finish panel.
- HINT:
- Tape the screwdriver tip before use.
| 3. REMOVE COMBINATION METER ASSEMBLY |
![]() ![]() |
Remove the 2 screws.
Pull the combination meter as indicated by the arrow in the illustration to detach the 2 clips.
Disconnect the connector and remove the combination meter.
| 4. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER |
![]() ![]() |
Using a screwdriver, detach the 3 clips, 3 claws and remove the cluster finish panel, then disconnect the connector.
- HINT:
- Tape the screwdriver tip before use.
| 5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER |
![]() ![]() |
Using a screwdriver, detach the 3 clips, 3 claws and remove the cluster finish panel, then disconnect the connector.
- HINT:
- Tape the screwdriver tip before use.
| 6. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver) |
Remove the radio receiver with bracket (Click here).
| 7. REMOVE STEREO OPENING COVER (w/o Radio Receiver) |
![]() ![]() |
Remove the 4 bolts.
Detach the 4 clips and remove the stereo opening cover.
| 8. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY CENTER |
![]() ![]() |
Using a screwdriver, detach the 5 clips and remove the instrument panel register.
- HINT:
- Tape the screwdriver tip before use.
| 9. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() ![]() |
Open the glove compartment door.
Detach the claw from the glove compartment door stopper.
While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, open the door to release it from the 2 stoppers.
Open the door until it is horizontal.

Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.

| 10. REMOVE FRONT PILLAR GARNISH LH |
for Long Body (Click here)
| 11. REMOVE FRONT PILLAR GARNISH RH |
for Long Body (Click here)
| 12. REMOVE UPPER INSTRUMENT PANEL |
![]() ![]() |
Remove the 2 bolts from the passenger airbag.
Disconnect the passenger airbag connector.
Remove the 2 bolts and 2 screws.
Disconnect the connectors and clamps.
Detach the 6 clips and 5 claws and remove the instrument panel.


| 13. REMOVE ANTENNA CORD SUB-ASSEMBLY |
Disconnect the connector.
Detach the 4 clamps and remove the antenna cord.


| 14. REMOVE ROOF HEADLINING ASSEMBLY (for Short Body) |
Remove the roof headlining (Click here).
| 15. REMOVE ROOF HEADLINING ASSEMBLY (for Long Body) |
Remove the roof headlining (Click here).
| 16. REMOVE ANTENNA CORD SUB-ASSEMBLY |
for Short Body (w/o Sliding Roof):
Apply masking tape to the antenna cord to mark it.
- HINT:
- Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.
Remove the antenna cord from the roof headlining.
Remove the double-sided tape from the roof headlining.


for Short Body (w/ Sliding Roof):
Apply masking tape to the antenna cord to mark it.
- HINT:
- Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.
Remove the antenna cord from the roof headlining.
Remove the double-sided tape from the roof headlining.


for Long Body (w/o Sliding Roof):
Apply masking tape to the antenna cord to mark it.
- HINT:
- Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.
Remove the antenna cord from the roof headlining.
Remove the double-sided tape from the roof headlining.


for Long Body (w/ Sliding Roof):
Apply masking tape to the antenna cord to mark it.
- HINT:
- Apply the masking tape so that the edges of the masking tape and roof headlining are aligned as shown in the illustration.
Remove the antenna cord from the roof headlining.
Remove the double-sided tape from the roof headlining.










