INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL COMMON RAIL ASSEMBLY |
Install the intake manifold insulator and common rail with the 2 bolts.

- Torque:
- 20.5 N*m{ 209 kgf*cm , 15 ft.*lbf }
Using pliers, grip the claws of the clip and slide the clip to connect the fuel hose as shown in the illustration.
| 2. INSTALL INJECTION PIPE SUB-ASSEMBLY |
- NOTICE:
- In a case where the common rail is replaced, the injection pipes must also be replaced.
Temporarily install the 4 injection pipes.

Using SST, tighten the 4 nuts at the common rail end of the injection pipes.
- SST
- 09023-38401
- Torque:
- 27 N*m{ 275 kgf*cm , 20 ft.*lbf }
- HINT:
- Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
- Make sure that the pipe is not deformed or twisted during installation.
If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.
- Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
Using SST, tighten the 4 nuts at the injector end of the injection pipes.
- SST
- 09023-38401
- Torque:
- 27 N*m{ 275 kgf*cm , 20 ft.*lbf }
- HINT:
- Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
- Make sure that the pipe is not deformed or twisted during installation.
If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.
- Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
| 3. INSTALL FUEL INLET PIPE SUB-ASSEMBLY |
- NOTICE:
- In a case where the common rail is replaced, the fuel inlet pipe must also be replaced.
- In a case where the common rail is replaced, the fuel inlet pipe must also be replaced.
Temporarily install the fuel inlet pipe with the 2 clamps and nut.

Using SST, tighten the nut at the common rail end of the fuel inlet pipe.
- SST
- 09023-38401
- Torque:
- 27 N*m{ 275 kgf*cm , 15 ft.*lbf }
- HINT:
- Use of the proper SST is required to ensure that the correct torque is applied to the inlet pipe nut.
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
- Make sure that the pipe is not deformed or twisted during installation.
If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.
- Use of the proper SST is required to ensure that the correct torque is applied to the inlet pipe nut.
Using SST, tighten the nut at the supply pump end of the fuel inlet pipe.
- SST
- 09023-38401
- Torque:
- 27 N*m{ 275 kgf*cm , 20 ft.*lbf }
- HINT:
- Use of the proper SST is required to ensure that the correct torque is applied to the inlet pipe nut.
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
- Make sure that the pipe is not deformed or twisted during installation.
If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.
- Use of the proper SST is required to ensure that the correct torque is applied to the inlet pipe nut.
Tighten the fuel inlet pipe clamp nut.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
| 4. CONNECT ENGINE WIRE |
Connect the engine wire to the engine cover bracket.
Connect the glow plug wire harness.
Install the 2 nuts.
Install the nut and grommet.
- Torque:
- 2.2 N*m{ 22 kgf*cm , 19 in.*lbf }
Connect the turbo pressure sensor connector.
Connect the pressure discharge valve connector.
Connect the fuel pressure sensor.
| 5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 6. BLEED AIR FROM FUEL SYSTEM |
Using the hand pump indicated by the arrows in the illustration, bleed the fuel system. Continue pumping until pumping becomes difficult.

| 7. CHECK FOR FUEL LEAKS |
Perform the ACTIVE TEST.

Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test.
Intelligent Tester Display
Test Details
Control Range
Diagnostic Notes
Test the Fuel Leak
Pressurizing common rail internal fuel pressure, and checking for fuel leaks
Stop/Start
- Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when Start is selected
- Above conditions to be maintained while test is Start
- Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when Start is selected
| 8. INSTALL NO. 1 ENGINE COVER |
Attach the 4 clips to install the engine cover.

