2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FUEL SUPPLY PUMP ASSEMBLY
  1. Install a new O-ring to the supply pump.

  1. A114894
    Install the supply pump drive coupling.

    NOTICE:
    When reusing the coupling, it must be installed in the same orientation (top/bottom, front/back) as when it was removed,

    HINT:
    Line up the coupling with the groove in the camshaft end.

  1. Install the supply pump with the 2 bolts.

    Torque:
    20.5 N*m{ 209 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Apply engine oil on the O-ring of the supply pump.

    HINT:
    Line up the end of the supply pump drive shaft with the supply pump drive coupling.

  1. A110786
    Connect the suction control valve connector.

  1. Connect the fuel temperature sensor connector.


2. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
In a case where the supply pump is replaced, the fuel inlet pipe must also be replaced.

  1. A114992E05
    Temporarily install the fuel inlet pipe with the 2 clamps and nut.

  1. Using SST, first tighten the nut at the common rail end of the fuel inlet pipe.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the inlet pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
    4. If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Using SST, tighten the nut at the supply pump end of the fuel inlet pipe.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the inlet pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
    4. If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Tighten the fuel inlet pipe clamp nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


3. INSTALL FUEL TUBE SUB-ASSEMBLY

  1. A114893
    Install a new gasket and the fuel tube with the union bolt.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

  1. A117977
    Turn the retainer in the direction indicated by the arrow until the retainer stops.

  1. A117978
    Insert the fuel tube connector into the injector.

  1. A117979
    Turn the retainer in the direction indicated by the arrow until it makes a "click" sound.

    NOTICE:
    If the fuel tube connector is not inserted to the correct position in the injector, the retainer cannot be turned farther in the direction of the arrow.

  1. A114936
    Connect the exhaust fuel addition injector connector.


4. INSTALL NO. 1 FUEL HOSE

  1. A133977
    Using pliers, grip the claws of the 2 clips and slide the 2 clips to install the No. 1 fuel hose.


5. INSTALL NO. 3 FUEL HOSE

  1. A114956E03
    Using pliers, grip the claws of the 2 clips and slide the 2 clips to install the No. 3 fuel hose as shown in the illustration.


6. INSTALL AIR CLEANER ASSEMBLY

  1. A124928E01
    Install the cleaner case with the 3 bolts and connect the wire harness clamp.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air filter element.

  1. A126824
    Using pliers, grip the claws of the clip to install the air cleaner cap.

  1. Using pliers, grip the claws of the clip and slide the clip to connect the PCV hose.

  1. A124929E01
    Insert the hinge parts of the air cleaner cap into the air cleaner case, and then hang the 3 hook clamps.

  1. Connect the mass air flow meter connector.

  1. Attach the wire harness clamp.


7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

8. BLEED AIR FROM FUEL SYSTEM

  1. A130544
    Using the hand pump indicated by the arrows in the illustration, bleed the fuel system. Continue pumping until pumping becomes difficult.


9. INSPECT FOR FUEL LEAK

  1. B127990E01
    Perform the ACTIVE TEST.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Turn the intelligent tester ON.

    4. Enter the following menus: Powertrain / Engine / Active Test.

    5. Perform the Active Test.

      Intelligent Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizing common rail internal fuel pressure, and checking for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when Start is selected
      2. Above conditions to be maintained while test is Start


10. INSTALL NO. 1 ENGINE COVER

  1. A123518
    Attach the 4 clips to install the engine cover.


11. INITIALIZE THE LEARNING VALUE OF THE SUPPLY PUMP ASSEMBLY
  1. Perform initialization procedure (Click here).

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →