2005-2008 RAV4 · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FRONT DIFFERENTIAL SIDE GEAR

  1. C117507
    Coat the rotating surface of the front differential side gear with gear oil.

  1. Install the 2 front differential side gears and 2 front differential side gear thrust washers onto the front differential case.


2. INSTALL FRONT DIFFERENTIAL PINION

  1. C083566
    Coat the rotating surface of the front differential pinion with gear oil.

  1. Install the 2 front differential side gear thrust washers and 2 front differential pinions from the differential case.

    HINT:
    Install the 2 front differential pinions with the front differential washers while turning the front differential pinion.

  1. C117493
    Install the pinion shaft into the differential case.

  1. C117496
    Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

    Standard backlash:
    0.05 to 0.20 mm (0.0020 to 0.0079 in.)

    If the backlash is not within the specifications, install a thrust washer of a different thickness.

    Standard thrust washer thickness:
    Thickness
    Thickness
    1.23 to 1.27 mm (0.0484 to 0.0500 in.)
    1.63 to 1.67 mm (0.0642 to 0.0657 in.)
    1.28 to 1.32 mm (0.0504 to 0.0520 in.)
    1.68 to 1.72 mm (0.0661 to 0.0677 in.)
    1.33 to 1.37 mm (0.0524 to 0.0539 in.)
    1.73 to 1.77 mm (0.0681 to 0.0697 in.)
    1.38 to 1.42 mm (0.0543 to 0.0559 in.)
    1.78 to 1.82 mm (0.0701 to 0.0717 in.)
    1.43 to 1.47 mm (0.0583 to 0.0579 in.)
    1.83 to 1.87 mm (0.0720 to 0.0736 in.)
    1.48 to 1.52 mm (0.0583 to 0.0598 in.)
    1.88 to 1.92 mm (0.0740 to 0.0756 in.)
    1.53 to 1.57 mm (0.0602 to 0.0618 in.)
    1.93 to 1.97 mm (0.0760 to 0.0776 in.)
    1.58 to 1.62 mm (0.0622 to 0.0638 in.)
    -

  1. C117494
    Using a pin punch and hammer, tap in the pinion shaft slotted spring pin through the front differential case and the hole in the pinion shaft.

  1. C117495
    Using a hammer and chisel, caulk the pin holes around the circumference of the front differential case.


3. INSTALL FRONT DIFFERENTIAL RING GEAR

  1. C092888E02
    Using a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

  1. Clean the contact surface of the front differential case.

  1. C117489E02
    Aligning the matchmarks, quickly install the front differential ring gear onto the front differential case with the 16 bolts.

    Torque:
    106 N*m{ 1,081 kgf*cm , 78 ft.*lbf }


4. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

  1. C117497E01
    Using SST and a press, press in a new tapered roller bearing.
    SST
    09309-14010  


5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

C133923E01
  1. Using SST and a press, press in a new tapered roller bearing.

    SST
    09554-22010  

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →