2005-2008 RAV4 · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Aug 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL FRONT BUMPER SIDE RETAINER LH

B209172
  1. Install the retainer with the clip.

  1. Install the bolt.


2. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the procedure described for the LH side.


3. INSTALL FRONT BUMPER REINFORCEMENT
  1. Install the reinforcement with the 8 bolts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

  1. Attach the 3 clamps to install the wire harness.

    B209928E01


4. INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

B211609
  1. Install the reinforcement with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


5. INSTALL LOW PITCHED HORN ASSEMBLY

E173377
  1. Install the horn with the bolt.

    Torque:
    19.5 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Connect the horn connector.


6. INSTALL HIGH PITCHED HORN ASSEMBLY

E173376
  1. Install the horn with the bolt.

    Torque:
    19.5 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Connect the horn connector.


7. INSTALL FRONT BUMPER CENTER STAY SUB-ASSEMBLY

  1. Install the stay with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


    B209927E01


8. INSTALL FRONT BUMPER LOWER ABSORBER (w/ Front Bumper Lower Absorber)

B208312
  1. Install the lower absorber.


9. INSTALL FRONT BUMPER ENERGY ABSORBER (w/ Front Bumper Lower Absorber)

B208311
  1. Install the 2 energy absorbers.


10. INSTALL FRONT NO. 2 BUMPER ENERGY ABSORBER

  1. Install the energy absorber.

    B209931E01


11. INSTALL FRONT BUMPER COVER

B208306
  1. w/ Fog Light:
    Connect the 2 fog light connectors.

  1. Attach the 4 claws to install the bumper cover.

  1. B209171
    Install the 8 screws and 4 clips.

  1. B209204
    Install the retainer.

    HINT:
    Use the same procedure for the RH and LH sides.

  1. Position the groove on the pin hold clip vertically and insert the clip to install it.

    NOTICE:
    Make sure that the groove on the pin hold clip is positioned vertically.

    HINT:
    Use the same procedure for the RH and LH sides.


12. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

B208332
  1. Install the splash shield with the nut, bolt and screw.


13. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

HINT:
Use the procedure described for the LH side.


14. INSTALL RADIATOR GRILLE PROTECTOR

B209174
  1. Install the 2 radiator grille protectors.


15. INSTALL CENTER HOOD CUSHION

B209173
  1. Install the hood cushion.


16. INSTALL RADIATOR SUPPORT OPENING COVER

B209240
  1. Install the radiator support opening cover with the 9 clips.

← INSTALLATION (Nov 2005 – Jul 2008)COMPONENTS (Nov 2005 – Jul 2008) →