2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL EXHAUST GAS TEMPERATURE SENSOR (for Rear Side)

  1. A117742
    Temporarily install the sensor with the 2 nuts and union nut.

  1. A116327
    Tighten the 2 nuts.

    Torque:
    6.4 N*m{ 65 kgf*cm , 57 in.*lbf }

  1. A116329E02
    Using SST, tighten the union nut.
    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for use with SST
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for use without SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).


2. INSTALL EXHAUST GAS TEMPERATURE SENSOR (for Front Side)
  1. Temporarily install the sensor with the union nut.

  1. A116328E03
    Using SST, tighten the union nut.
    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf } for use with SST
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for use without SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).


3. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A110789
    Temporarily install a new gasket and the exhaust manifold converter with the 3 nuts.

  1. A110768
    Temporarily install the No. 2 exhaust manifold stay with the 2 bolts and nut.

  1. A110790
    Temporarily install the No. 2 manifold stay with the 3 bolts.

  1. A160474
    Temporarily install the No. 1 manifold stay with the bolt and nut.

  1. A116310
    Tighten the 2 bolts holding the No. 2 exhaust manifold stay to the cylinder block.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

    NOTICE:
    Make sure to tighten the upper bolt first and the lower bolt last.

  1. A133243E02
    While pushing the manifold converter towards the cylinder block, tighten the 3 nuts holding the exhaust manifold converter to the turbocharger.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. A116309
    Tighten the nut holding the No. 2 exhaust manifold stay to the exhaust manifold converter.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

  1. A116307
    Tighten the bolt holding the No. 2 manifold stay to the exhaust manifold converter.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

    HINT:
    Ensure that the stay is pushed flush to the cylinder block and manifold converter while tightening.

  1. A116308
    Tighten the 2 bolts holding the No. 2 manifold stay to the cylinder block.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

  1. A160475
    Tighten the bolt holding the No. 1 manifold stay to the cylinder head.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Ensure that the stay is pushed flush to the cylinder head and manifold converter while tightening.

  1. A160463
    Tighten the nut holding the No. 1 manifold stay to the exhaust manifold converter.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


4. INSTALL NO. 2 MANIFOLD CONVERTER INSULATOR

  1. A114858
    Install the manifold converter insulator with the 3 nuts.

    Torque:
    29 N*m{ 291 kgf*cm , 21 ft.*lbf }


5. INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR

  1. A114857
    Install the manifold converter insulator with the 5 bolts.

    Torque:
    29 N*m{ 291 kgf*cm , 21 ft.*lbf }


6. INSTALL ENGINE ASSEMBLY
  1. Install the engine assembly to the vehicle (Click here).


7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
← INSPECTION (from Jan 2007)INSTALLATION (from Aug 2007) →