2005-2008 RAV4 · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built from Aug 2007

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

In this system, the signals of the duplex type stop light switch (STP and ST1-) are used to judge whether the brake system is abnormal. When signals that indicate depressing and releasing the brake pedal are detected simultaneously, the ECM interprets this as a malfunction of the stop light switch.

HINT:
Normal conditions are shown in the table below.
Signal
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF

DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a), (b) and (c) continue for 0.5 seconds or more:
(1 trip detection logic)
(a) Ignition switch is on (IG)
(b) Brake pedal is released
(c) STP signal is OFF when ST1- signal is OFF
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

WIRING DIAGRAM

C128777E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK STOP LIGHT SWITCH
  1. Check if the stop lights turn ON and OFF when the brake pedal is depressed and released.

    OK:
    Stop lights turn ON and OFF normally.



NG
REPAIR OR REPLACE STOP LIGHT SWITCH
OK


2. CHECK STP SIGNAL

  1. C129061E01
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Check the result.

    OK:
    Brake Pedal
    Specified Condition
    Depressed
    STP signal ON
    Released
    STP signal OFF



OK
CHECK FOR INTERMITTENT PROBLEMS
NG


3. INSPECT STOP LIGHT SWITCH

  1. A072924E23
    Disconnect the stop light switch connector.

  1. Measure the resistance of the stop light switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin not pushed
    10 kΩ or higher
    1 - 2
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin pushed
    Below 1 Ω

  1. Reconnect the stop light switch connector.



NG
REPLACE STOP LIGHT SWITCH
OK


4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)

  1. A128658E02
    Disconnect the stop light switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A5-1 - A12-35 (STP)
    Below 1 Ω
    A5-4 - A12-34 (ST1-)
    Below 1 Ω
    A5-1 or A12-35 (STP) - Body ground
    10 kΩ or higher
    A5-4 or A12-34 (ST1-) - Body ground
    10 kΩ or higher

  1. Reconnect the stop light switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0504 Brake Switch "A" / "B" Correlation (Jan 2007 – Jul 2007)P0516 Battery Temperature Sensor Circuit Low (+ P0517) (Jan 2007 – Jul 2007) →