2005-2008 RAV4 · Service Manual ENGINE

P0200 Injector Circuit / Open

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The EDU drives the injectors at high speeds. The EDU delivers high-speed drive signals under high-pressure fuel conditions using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the EDU receives an injection command (#) signal from the ECM, the EDU responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector.
C129056E01
DTC No.
DTC Detection Condition
Trouble Area
P0200
Open or short in EDU or injector circuit
After engine is started, there is no INJF signal from EDU to ECM, despite ECM sending # signals to EDU
(1 trip detection logic)
  1. Open or short in EDU circuit
  2. Injector
  3. EDU
  4. ECM

HINT:
DTC P0200 is detected when starting the engine and letting it idle for 30 seconds.


MONITOR DESCRIPTION

  1. P0200 (Open or short in EDU or injector circuit):
    The ECM continuously monitors both injection command (#) signals and injection confirmation (INJF) signals. This DTC will be set if the ECM determines that the number of # signals and INJF signals are inconsistent.
    The injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU (injector drive circuit), in relation to the current drawn by the injector. When the injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.
    P0200 refers to a malfunction in the EDU or injector circuit.
    If this DTC is set, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.
    C129057E01

MONITOR STRATEGY

Required sensors
INJF signal from EDU
Frequency of operation
Continuous
Duration
10 seconds
MIL operation
1 driving cycle

TYPICAL ENABLING CONDITIONS

Item
Specification
Specification
Minimum
Maximum
Engine speed
500 rpm
-
Battery voltage
11 V
-
Ignition switch
on (IG)
on (IG)

TYPICAL MALFUNCTION THRESHOLDS

Threshold
The injection missing counter* for all the cylinders, or for one individual cylinder, reaches a specified number (taking approximately 1 second after starting the engine)
*: Increments when no INJF signal is received from the EDU despite the ECM sending # signals

WIRING DIAGRAM

C128781E01
C128782E01

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing an injector, the ECM needs registration (Click here).


1. INSPECT INJECTOR ASSEMBLY

  1. C129058E01
    Disconnect the B36, B37, B38, and B39 injector connectors.

  1. Measure the resistance of the injector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    0.9 to 1.1 MΩ

  1. Reconnect the injector connectors.



NG
REPLACE INJECTOR ASSEMBLY
OK


2. CHECK WIRE HARNESS (INJECTOR - EDU)
A128634E01
  1. Disconnect the B36, B37, B38, and B39 injector connectors.

  1. Disconnect the B50 and B58 EDU connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B36-1 - B58-2 (IJ1+)
    Below 1 Ω
    B37-1 - B58-5 (IJ2+)
    Below 1 Ω
    B38-1 - B58-4 (IJ3+)
    Below 1 Ω
    B39-1 - B58-1 (IJ4+)
    Below 1 Ω
    B36-2 - B50-4 (IJ1-)
    Below 1 Ω
    B37-2 - B50-5 (IJ2-)
    Below 1 Ω
    B38-2 - B50-6 (IJ3-)
    Below 1 Ω
    B39-2 - B50-1 (IJ4-)
    Below 1 Ω
    B36-1 or B58-2 (IJ1+) - Body ground
    10 kΩ or higher
    B37-1 or B58-5 (IJ2+) - Body ground
    10 kΩ or higher
    B38-1 or B58-4 (IJ3+) - Body ground
    10 kΩ or higher
    B39-1 or B58-1 (IJ4+) - Body ground
    10 kΩ or higher
    B36-2 or B50-4 (IJ1-) - Body ground
    10 kΩ or higher
    B37-2 or B50-5 (IJ2-) - Body ground
    10 kΩ or higher
    B38-2 or B50-6 (IJ3-) - Body ground
    10 kΩ or higher
    B39-2 or B50-1 (IJ4-) - Body ground
    10 kΩ or higher

  1. Reconnect the injector connectors.

  1. Reconnect the EDU connectors.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. CHECK WIRE HARNESS (EDU - ECM)

  1. A128590E01
    Disconnect the B51 EDU connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B51-12 (#10) - B32-50 (#1)
    Below 1 Ω
    B51-10 (#20) - B32-49 (#2)
    Below 1 Ω
    B51-9 (#30) - B32-48 (#3)
    Below 1 Ω
    B51-11 (#40) - B32-47 (#4)
    Below 1 Ω
    B51-6 (INJF) - B32-51 (INJF)
    Below 1 Ω
    B51-12 (#10) or B32-50 (#1) - Body ground
    10 kΩ or higher
    B51-10 (#20) or B32-49 (#2) - Body ground
    10 kΩ or higher
    B51-9 (#30) or B32-48 (#3) - Body ground
    10 kΩ or higher
    B51-11 (#40) or B32-47 (#4) - Body ground
    10 kΩ or higher
    B51-6 (INJF) or B32-51 (INJF) - Body ground
    10 kΩ or higher

  1. Reconnect the EDU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. CHECK EDU

  1. A114029E04
    Disconnect the B50 EDU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    B50-3 (+B) - B50-2 (GND)
    9 to 14 V

  1. Reconnect the EDU connector.



NG
CHECK EDU POWER SOURCE CIRCUIT
OK


5. REPLACE EDU
  1. Replace the EDU.


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine and drive the vehicle for approximately 15 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0200
    A
    No output
    B



B
SYSTEM IS OK
A

REPLACE ECM


← P0191 Fuel Rail Pressure Sensor Circuit Range / Performance (from Nov 2005)P0200 Injector Circuit / Open (from Jan 2007) →