P0087 Fuel Rail / System Pressure - Too Low
Diagnostic trouble codes · Vehicles built from Jan 2007
Also covers:
- P0190 Fuel Rail Pressure Sensor Circuit
- P0192 Fuel Rail Pressure Sensor Circuit Low Input
- P0193 Fuel Rail Pressure Sensor Circuit High Input
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure to the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs the voltage in proportion to the internal fuel pressure.

| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0087 |
Fuel pressure sensor output voltage stays at fixed value (1 trip detection logic) |
|
| P0190 |
Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or more for 0.5 seconds (1 trip detection logic) |
|
| P0192 |
Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds (1 trip detection logic) |
|
| P0193 |
Fuel pressure sensor output voltage is 4.9 V or more for 0.5 seconds (1 trip detection logic) |
|
- HINT:
- For more information on the fuel pressure sensor and common rail system, refer to the system description (Click here).
- When DTC P0087, P0190, P0192 and/or P0193 is set, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.
- For more information on the fuel pressure sensor and common rail system, refer to the system description (Click here).
Reference: Engine Speed
Fuel Pressure
Idling
Approximately 27 to 37 MPa
3,000 rpm (No engine load)
Approximately 63 to 71 MPa
MONITOR DESCRIPTION
- P0087 (Fuel pressure sensor output stays at fixed value):
Under normal conditions, the internal fuel pressure of the common rail usually fluctuates 1 to 2 MPa (10 to 20 kgf/cm2, 145 to 290 psi) even when the driving conditions are constant. The internal fuel pressure is approximately 35 to 40 MPa (357 to 408 kgf/cm2, 5,079 to 5,805 psi) when idling, and it increases to approximately 78 to 88 MPa (796 to 888 kgf/cm2, 11,320 to 12,627 psi) when running the engine at 3,000 rpm. This DTC is set if there is no fluctuation of the fuel pressure.
If this DTC is set, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.

- P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):
These DTCs are set if the fuel pressure sensor output voltage is out of the standard range and an open or short malfunction of the sensor circuit has occurred.
If these DTCs are set, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.
MONITOR STRATEGY
| Required Sensors |
Fuel pressure sensor |
| Frequency of operation |
Continuous |
| Duration |
1 second |
| MIL operation |
1 driving cycle |
| Required Sensors |
Fuel pressure sensor |
| Frequency of operation |
Continuous |
| Duration |
0.5 seconds |
| MIL operation |
1 driving cycle |
| Required Sensors |
Fuel pressure sensor |
| Frequency of operation |
Continuous |
| Duration |
0.5 seconds |
| MIL operation |
1 driving cycle |
| Required Sensors |
Fuel pressure sensor |
| Frequency of operation |
Continuous |
| Duration |
0.5 seconds |
| MIL operation |
1 driving cycle |
TYPICAL ENABLING CONDITIONS
| Item |
Specification |
| Minimum | |
| Engine speed |
500 rpm |
| Battery voltage |
8 V |
| Fuel volume |
5 mm3
|
| The monitor will not run if the fuel pressure sensor circuit (P0190, P0192 and P0193) is malfunctioning. | |
TYPICAL MALFUNCTION THRESHOLDS
| Detection Criteria |
Threshold |
| Changing value of fuel pressure |
Virtually no fluctuation |
| Detection Criteria |
Threshold |
| Fuel pressure sensor output voltage |
Less than 0.55 V or more than 4.9 V |
| Detection Criteria |
Threshold |
| Fuel pressure sensor output voltage |
Less than 0.55 V |
| Detection Criteria |
Threshold |
| Fuel pressure sensor output voltage |
More than 4.9 V |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- After completing repairs, check that P0087, P0190, P0192 and/or P0193 is not set again.
- If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.
- After completing repairs, check that P0087, P0190, P0192 and/or P0193 is not set again.
| 1. READ VALUE USING FUEL PRESSURE SENSOR |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Read the values.
- OK:
- The internal fuel pressure of the common rail is within the specification below.
Engine Speed
Fuel Pressure
Idling
Approximately 35 to 40 MPa
3,000 rpm (No engine load)
Approximately 78 to 88 MPa
|
|
||||
| OK | |
| 2. CHECK IF DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC / Clear.
Clear the DTCs (Click here).
Let the engine idle for 60 seconds, and then repeat quick engine RPM accelerations (to 2,500 rpm) for 30 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0087, P0190, P0192 or P0193
A
No output
B
|
|
||||
| A | ||
| ||
| 3. CHECK WIRE HARNESS (FUEL PRESSURE SENSOR - ECM) |
Disconnect the B60 fuel pressure sensor connector.

Disconnect the B32 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
B60-2 (PR) - B32-67 (PCR1)
Below 1 Ω
B60-3 (VC) - B32-69 (VCM)
Below 1 Ω
B60-1 (E2) - B32-91 (E2M)
Below 1 Ω
B60-2 (PR) or B32-67 (PCR1) - Body ground
10 kΩ or higher
B60-3 (VC) or B32-69 (VCM) - Body ground
10 kΩ or higher
B60-1 (E2) or B32-91 (E2M) - Body ground
10 kΩ or higher
Reconnect the fuel pressure sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
