2005-2008 RAV4 · Service Manual ENGINE

P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance

Diagnostic trouble codes · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.
P0488 
DTC Detection Condition
DTC Detection Drive Pattern
Trouble Area
The throttle motor activation duty is less than 10% or greater than 90% for 30 seconds (1 trip detection logic).

HINT:
The throttle valve commanded duty can be read using the tester in the Data List item Throttle Motor Duty.

Over a period of 10 seconds or more, slowly raise engine speed to 3000 rpm and lower it to idle
  1. Throttle valve stuck
  2. Throttle valve does not move smoothly
  3. Open or short in throttle control motor circuit
  4. ECM
Related Data List 
DTC No.
Data List
P0488
  1. Throttle Motor DUTY
  2. Actual Throttle Position
Reference 
Condition
Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm
Throttle valve opening angle varies smoothly

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio controlled voltage signal. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.
A128641E07

WIRING DIAGRAM

Refer to DTC P0120 (Click here).

INSPECTION PROCEDURE

NOTICE:
When cleaning the EGR valve or the diesel throttle body, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.


HINT:
If carbon deposits exist in the diesel throttle body assembly, the following parts possibly also have deposits inside: The EGR valve assembly, intake manifold, catalyst, and other parts related to the exhaust gas.
By removing the EGR valve assembly from the intake manifold, the carbon deposit condition between the EGR valve and intake manifold can be checked visually. When checking for deposits in the EGR valve assembly, hold the EGR valve to a light and confirm that the valve contacts with the valve seat securely.
A201142E01


1. READ VALUE USING INTELLIGENT TESTER (ACTUAL THROTTLE POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Record the stored DTC and Freeze Frame Data.

  1. Clear the DTC.

  1. Turn the ignition switch to off and wait for 5 seconds or more.

    HINT:
    Be sure to turn off the ignition switch before performing this inspection. The fully closed position of the diesel throttle valve is learned when the ignition switch is turned off.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Throttle Position.

  1. Read the value.

    Standard:
    Engine Condition
    Specified Condition
    Ignition switch ON
    -5 to 5%
    Idling
    (after engine warmed up, at an altitude near sea level)
    81 to 95%
    Accelerator pedal fully depressed
    -5 to 5%
    and value changes smoothly in transition

    HINT:
    1. Check the Throttle Motor DUTY in the Data List items at the same time. If the value in Throttle Motor DUTY is outside the range of 50 +/-40% for 30 seconds or more, the throttle valve may not be sliding properly.
    2. The Actual Throttle Position in the Data List items is indicated as follows:

    Throttle Valve Condition
    Actual Throttle Position
    Fully closed
    100%
    Fully open
    0%

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Close Learning Val. and Diesel Throttle Learn Status.

  1. Read the values when the ignition switch is ON.

    Standard:
    Throttle Close Learning Val. is between 14.25 to 21.25 deg. and Diesel Throttle Learn Status is OK

    NOTICE:
    Extremely cold conditions might cause the throttle valve movement to be delayed.



NG
Go to step 3
OK


2. INSPECT VACUUM HOSE AND PIPE (BETWEEN INTERCOOLER AND INTAKE MANIFOLD)
  1. Check for water or water marks in the hoses and pipes between the intercooler and intake manifold.

    OK:
    No water or water marks in the hoses and pipes.

    HINT:
    If water or water marks exist, water may have frozen in the diesel throttle body. The DTC was possibly caused by the presence of ice.

  1. Inspect the hoses and pipes between the intercooler and intake manifold.

    OK:
    Hoses and pipes are not damaged, squashed, or disconnected.

    A190321E01



OK
Go to step 16

NG
REPAIR OR REPLACE HOSE OR PIPE
3. CHECK FOR DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

  1. Check for any deposits in the diesel throttle body assembly.

    OK:
    No deposits in the diesel throttle body assembly.

    HINT:
    If carbon deposits exist in the diesel throttle body assembly, the following parts possibly also have deposits inside: The EGR valve assembly, intake manifold, catalyst, and other parts related to the exhaust gas.
    By removing the EGR valve assembly from the intake manifold, the carbon deposit condition between the EGR valve and intake manifold can be checked visually. When checking for deposits in the EGR valve assembly, hold the EGR valve to a light and confirm that the valve contacts with the valve seat securely.

    A201145E01



OK
Go to step 7

NG
Go to step 4
4. CHECK FOR DEPOSIT (CLEAN THROTTLE BODY)
  1. Remove the deposits from the throttle body assembly and clean it.

    NOTICE:
    When cleaning the EGR valve or the diesel throttle body, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.


NEXT


5. INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
  1. Using your finger, check that the throttle valve moves smoothly.

    OK:
    Throttle valve moves smoothly.

    NOTICE:
    Take care that you do not damage the throttle valve and the valve housing.



NG
Go to step 12
OK


6. READ VALUE USING INTELLIGENT TESTER (ACTUAL THROTTLE POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the ignition switch off and wait for 5 seconds or more.

    HINT:
    Be sure to turn off the ignition switch before performing this inspection. The fully closed position of the diesel throttle valve is learned when the ignition switch is turned off.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Throttle Position.

  1. Read the values.

    Standard:
    Engine Condition
    Specified Condition
    Ignition switch ON
    -5 to 5%
    Idling
    (after engine warmed up, at an altitude near sea level)
    81 to 95%
    Accelerator pedal fully depressed
    -5 to 5%
    and value changes smoothly in transition

    HINT:
    Check the Throttle Motor DUTY in the Data List items at the same time. If the value in Throttle Motor DUTY is outside the range of 50 +/-40% for 30 seconds or more, the throttle valve may not be sliding properly.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Close Learning Val. and Diesel Throttle Learn Status.

  1. Read the values when the ignition switch is ON.

    Standard:
    Throttle Close Learning Val. is between 14.25 to 21.25 deg. and Diesel Throttle Learn Status is OK



OK
Go to step 16

NG
Go to step 8
7. INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
  1. Using your finger, check that the throttle valve moves smoothly.

    OK:
    Throttle valve moves smoothly.

    NOTICE:
    Take care that you do not damage the throttle valve and the valve housing.



NG
Go to step 12
OK


8. CHECK HARNESS AND CONNECTOR (POWER SOURCE OF DIESEL THROTTLE BODY)

  1. A201191E02
    Disconnect the B33 throttle control motor connector.

  1. Turn the ignition switch to ON

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B33-2 (B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the throttle control motor connector.



NG
Go to step 11
OK


9. CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT OF DIESEL THROTTLE BODY)

  1. A201191E01
    Disconnect the B33 throttle control motor connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B33-3 (RSC) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the throttle control motor connector.



NG
Go to step 11
OK


10. CHECK HARNESS AND CONNECTOR (ECM - DIESEL THROTTLE BODY)

  1. A130468E01
    Disconnect the B33 throttle control motor connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B33-1 (RSO) - B32-86 (LUSL)
    Below 1 Ω
    B33-1 (RSO) or B32-86 (LUSL) - Body ground
    10 kΩ or higher

  1. Reconnect the throttle control motor connector.

  1. Reconnect the ECM connector.



OK
Go to step 13

NG
Go to step 11
11. REPAIR OR REPLACE HARNESS OR CONNECTOR


NEXT
Go to step 16
12. REPLACE DIESEL THROTTLE BODY ASSEMBLY
  1. Replace the diesel throttle body assembly (Click here).



NEXT
Go to step 16
13. REPLACE DIESEL THROTTLE BODY ASSEMBLY
  1. Replace the diesel throttle body assembly (Click here).


NEXT


14. CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear DTCs.

  1. Turn the ignition switch to off and wait for 5 seconds or more.

    HINT:
    The fully closed position of the diesel throttle valve is learned when the ignition switch is turned off.

  1. Start the engine and warm it up.

  1. Drive the vehicle with a stop-and-go city drive pattern for more than 5 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P0488
    A
    No output
    B



B
END
A


15. REPLACE ECM
  1. Replace the ECM.

    NOTICE:
    After replacing the ECM, perform initialization (Click here) and registration (Click here).


NEXT


16. CHECK WHETHER DTC OUTPUT RECURS (DTCP0488)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear DTCs.

  1. Turn the ignition switch to off and wait for 5 seconds or more.

    HINT:
    The fully closed position of the diesel throttle valve is learned when the ignition switch is turned off.

  1. Start the engine and warm it up.

  1. Drive the vehicle with a stop-and-go city drive pattern for more than 5 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    OK:
    No DTCs are output.


NEXT

END


← P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance (Nov 2005 – Dec 2006)P0500 Vehicle Speed Sensor "A" (Nov 2005 – Dec 2006) →