2005-2008 RAV4 · Service Manual ENGINE

P0544 Exhaust GAS Temperature Sensor Circuit (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Aug 2007

Also covers:

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

A128649E02
The exhaust gas temperature sensors are installed front and behind the Diesel Particulate Filter (DPF) catalytic converter to sense the exhaust gas temperature.
A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the greater the thermistor resistance value. The greater the exhaust gas temperature, the lower the thermistor resistance value.
The exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the exhaust gas temperature sensor from terminal THCI (upstream) and THCO (downstream) via resistor R.
The resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with changes in the exhaust gas temperature, the voltage at terminals THCI (upstream) and THCO (downstream) also change. Based on these signals, when DPF catalyst regeneration is needed, the ECM operates the exhaust fuel addition injector to obtain target upstream temperature of the DPF catalytic converter as mentioned through sensor 1. In addition, the ECM monitors the rate of DPF catalytic converter temperature increase using sensor 2.
DTC No.
DTC Detection Condition
Trouble Area
P0544
Sensor 1 output is less than 0.2 V or more than 4.95 V for 3 seconds or more
(1 trip detection logic)
  1. Open or short in exhaust gas temperature sensor (on upstream) circuit
  2. Exhaust gas temperature sensor (on upstream)
  3. ECM
P0545
Sensor 1 output is less than 0.2 V for 3 seconds or more
(1 trip detection logic)
P0546
Sensor 1 output is more than 4.95 V for 3 seconds or more
(1 trip detection logic)
P2031
Sensor 2 output is less than 0.2 V or more than 4.95 V for 3 seconds or more
(1 trip detection logic)
  1. Open or short in exhaust gas temperature sensor (on downstream) circuit
  2. Exhaust gas temperature sensor (on downstream)
  3. ECM
P2032
Sensor 2 output is less than 0.2 V for 3 seconds or more
(1 trip detection logic)
P2033
Sensor 2 output is more than 4.95 V for 3 seconds or more
(1 trip detection logic)

HINT:
  1. DTC P1386 (Exhaust fuel addition injector malfunction) will be present if there is an open malfunction in an exhaust gas temperature sensor circuit.
  2. Sensor 1 represents a sensor located upstream on the DPF catalytic converter.
  3. Sensor 2 represents a sensor located downstream on the DPF catalytic converter.
  4. After confirming DTC P0544, P0545, P0546, P2031, P2032, and P2033, check the upstream and downstream exhaust gas temperature in the "Powertrain / Engine and ECT / Initial Exhaust Temp (IN) and Initial Exhaust Temp (OUT)" menu using the intelligent tester.
Reference: 
Condition
Exhaust Gas Temperature
Exhaust Gas Temperature Sensor Condition
Idling after warm-up
Constant at 50 to 700°C (122 to 1,292°F)
Normal
0°C (32°F)
Short circuit
1,000°C (1,832°F)
Open circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit, and illuminates the MIL.

WIRING DIAGRAM

C128780E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. READ VALUE USING EXHAUST GAS TEMPERATURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Initial Exhaust Temp (IN) and Initial Exhaust Temp (OUT).

  1. Read the value.

    OK:
    Same as the actual exhaust gas temperature (50 to 700°C [122 to 1,292°F] during idling after warm-up), and varies after an engine speed of 3,000 rpm is maintained for 1 minute.


    Result:
    Temperature Displayed
    Proceed to
    1,000°C (1,832°F)
    A
    0°C (32°F) (After warming up the engine)
    B
    Same as the actual exhaust gas temperature (50 to 700°C [122 to 1,292°F] during idling after warm-up), and varies after maintaining the engine speed of 3,000 rpm for 1 minute after accelerating the engine from idling to 3,000 rpm
    C

    HINT:
    1. If there is a short circuit, the tester will indicate 0°C (32°F).
    2. If there is an open circuit, the tester will indicate 1,000°C (1,832°F).



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS
A


2. CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)

  1. A130315E06
    Disconnect the exhaust gas temperature sensor connector.

  1. Connect terminals 1 and 2 of the exhaust gas temperature sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC 3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Initial Exhaust Temp (IN) and Initial Exhaust Temp (OUT).

  1. Read the value.

    Standard value:
    0°C (32°F)

  1. Reconnect the exhaust gas temperature sensor connector.



OK
CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE EXHAUST GAS TEMPERATURE SENSOR.
NG


3. CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)

  1. A130316E06
    Disconnect the exhaust gas temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B56-2 - B32-122 (THCI) or B57-2 - B32-121 (THCO)
    Below 1 Ω
    B56-1 - B32-99 (ETCI) or B57-1 - B32-98 (ETCO)
    Below 1 Ω

  1. Reconnect the exhaust gas temperature sensor.

  1. Reconnect the ECM connector.



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A131553E01
    Disconnect the exhaust gas temperature sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Initial Exhaust Temp (IN) and Initial Exhaust Temp (OUT).

  1. Read the value.

    Standard value:
    0°C (32°F)

  1. Reconnect the exhaust gas temperature sensor connector.



OK
REPLACE EXHAUST GAS TEMPERATURE SENSOR
NG


5. CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)

  1. A130316E06
    Disconnect the exhaust gas temperature sensor connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B56-2 or B32-122 (THCI) - Body ground
    B57-2 or B32-121 (THCO) - Body ground
    10 kΩ or higher

  1. Reconnect the exhaust gas temperature sensor connector.

  1. Reconnect the ECM connector.



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

REPLACE ECM


← P0544 Exhaust GAS Temperature Sensor Circuit (Bank 1 Sensor 1) (+ 5 more codes) (Jan 2007 – Jul 2007)P0560 System Voltage (from Jan 2007) →