2005-2008 RAV4 · Service Manual CRUISE CONTROL SYSTEM

Cruise Control Switch Circuit

Circuit diagnosis · Vehicles built Nov 2005 – Jul 2007

Versions by build date: Nov 2005 – Jul 2007 from Aug 2007

DESCRIPTION

This circuit sends signals to the ECM depending on the cruise control main switch condition. The battery supplies positive (+) battery voltage to the cruise control main switch. Then terminal CCS of the ECM receives the voltage according to the switch condition.

WIRING DIAGRAM

E124659E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. E107091E05
    Check the Data List for proper functioning of the cruise control main switch.

    ECM:
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Main SW (Main)
    Cruise control main switch signal (Main CPU) / ON or OFF
    ON: Cruise control main switch is ON (Main CPU)
    OFF: Cruise control main switch is OFF (Main CPU)
    -
    Cancel SW
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch ON
    OFF: CANCEL switch OFF
    -
    SET/COAST SW
    - / SET switch signal / ON or OFF
    ON: - / SET switch ON
    OFF: - / SET switch OFF
    -
    RES/ACC SW
    + / RES switch signal / ON or OFF
    ON: + / RES switch ON
    OFF: + / RES switch OFF
    -

    OK:
    When cruise control main switch operation is performed, the results will be same as above.
    Result 
    Result
    Proceed to
    OK
    A
    NG (All items are defective)
    B
    NG (1 to 3 items are defective)
    C



A
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE CRUISE CONTROL MAIN SWITCH
B


2. INSPECT CRUISE CONTROL MAIN SWITCH
  1. Remove the cruise control main switch.

  1. Measure the resistance according to the value(s) in the table below.E106137E06

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A-3 (CCS) - A-1 (ECC)
    Neutral
    10 kΩ or higher
    + (ACCEL)/RES (RESUME)
    216 to 264 Ω
    - (COAST)/SET
    567 to 693 Ω
    CANCEL
    1,386 to 1,694 Ω
    Main Switch on
    Below 1 Ω



NG
REPLACE CRUISE CONTROL MAIN SWITCH
OK


3. CHECK WIRE HARNESS (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
E103330E18
  1. Disconnect the m1 connector from the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A-3 - b1-3
    Always
    Below 1 Ω
    A-1 - b1-4
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. INSPECT SPIRAL CABLE

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying.

  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.E124662E07

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    b1-3 - E10-1 (CCS)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    b1-4 - E10-2 (ECC)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

HINT:
The spiral cable makes a maximum of approximately 5 rotations.



NG
REPLACE SPIRAL CABLE
OK


5. CHECK WIRE HARNESS (SPIRAL CABLE - ECM AND BODY GROUND)
E124664E04

HINT:
*1: for 1AZ-FE, 2AZ-FE
*2: for 2AD-FHV, 2AD-FTV

  1. Disconnect the E10 cable connector.

  1. Disconnect the A12 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for 1AZ-FE, 2AZ-FE 
    Tester Connection
    Specified Condition
    E10-1 (CCS) - A12-40 (CCS)
    Below 1 Ω
    E10-2 (ECC) - Body ground

    for 2AD-FHV, 2AD-FTV:
    Tester Connection
    Specified Condition
    E10-1 (CCS) - A12-23 (CCS)
    Below 1 Ω
    E10-2 (ECC) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Clutch Switch Circuit (from Nov 2005)Cruise Control Switch Circuit (from Aug 2007) →