2005-2008 RAV4 · Service Manual ENGINE

P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. This accelerator pedal position sensor is a non-contact type.

The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.
A129363E01
DTC No.
DTC Detection Condition
(All of following are 1 trip detection logic)
Trouble Area
P2120
Condition (a) continues for 0.5 sec. or more:
(a) VPA is 0.4 V or less
(b) VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Accelerator pedal
  3. Accelerator pedal rod (arm) deformed
  4. ECM
P2122
VPA is 0.4 V or less for 0.5 sec. or more when VPA2 output indicate accelerator pedal is opened
  1. Accelerator pedal position sensor
  2. Open in VCPA circuit
  3. VPA circuit open or ground short
  4. Accelerator pedal
  5. Accelerator pedal rod (arm) deformed
  6. ECM
P2123
Condition (a) continues for 2.0 sec. or more:
(a) VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Open in EPA circuit
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM
P2125
Condition (a) or (b) continues for 0.5 sec. or more:
(a) VPA2 is 1.2 V or less
(b) VPA2 is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Accelerator pedal
  3. Accelerator pedal rod (arm) deformed
  4. ECM
P2127
VPA2 is 1.2 V or less for 0.5 sec. or more when VPA output indicates accelerator pedal is opened
  1. Accelerator pedal position sensor
  2. Open in VCP2 circuit
  3. VPA2 circuit open or ground short
  4. Accelerator pedal
  5. Accelerator pedal rod (arm) deformed
  6. ECM
P2128
Conditions (a) and (b) continue for 2.0 sec. or more:
(a) VPA2 is 4.8 V or more
(b) VPA is 0.4 V or more and VPA is 3.45 V or less
  1. Accelerator pedal position sensor
  2. Open in EPA2 circuit
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM
P2138
Condition (a) or (b) continues for 2.0 sec. or more:
(a) Difference between VPA and VPA2 is 0.02 V or less
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less
  1. VPA and VPA2 circuits are short circuited
  2. Accelerator pedal position sensor
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM

HINT:
When DTC P2120, P2122, P2123, P2125, P2127, P2128, or P2138 is detected, check the output voltage of the accelerator pedal position sensor by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Accel Position 1 and Accel Position 2.
-
Accelerator pedal position expressed as voltage output
Accelerator pedal position expressed as voltage output
Accelerator pedal position expressed as voltage output
Accelerator pedal position expressed as voltage output
-
Accelerator pedal released
Accelerator pedal released
Accelerator pedal depressed
Accelerator pedal depressed
Trouble Area
Accel Position 1
Accel Position 2
Accel Position 1
Accel Position 2
VCP circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
VPA circuit open or ground short
0 to 0.2 V
0.9 to 2.3 V
0 to 0.2 V
3.4 to 5.0 V
VPA2 circuit open or ground short
0.5 to 1.1 V
0 to 0.2 V
3.0 to 4.6 V
0 to 0.2 V
EP circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V


WIRING DIAGRAM

C128637E02

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. READ VALUE USING ACCELERATOR PEDAL POSITION SENSOR

  1. C129061E02
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position 1 and Accel Position 2.

  1. Read the values.

    Standard voltage:
    Accelerator Pedal
    Accel Position 1
    Accel Position 2
    Released
    0.6 to 1.0 V
    1.4 to 1.8 V
    Depressed
    3.4 to 3.8 V
    4.2 to 4.6 V



OK
Go to step 5
NG


2. CHECK WIRE HARNESS (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A128721E01
    Disconnect the A6 accelerator pedal position sensor connector.

  1. Disconnect the A12 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A6-1 (VCP2) - A12-56 (VCP2)
    Below 1 Ω
    A6-2 (EPA2) - A12-58 (EPA2)
    Below 1 Ω
    A6-3 (VPA2) - A12-54 (VPA2)
    Below 1 Ω
    A6-4 (VCPA) - A12-55 (VCPA)
    Below 1 Ω
    A6-5 (EPA) - A12-57 (EPA)
    Below 1 Ω
    A6-6 (VPA) - A12-53 (VPA)
    Below 1 Ω
    A6-1 (VCP2) or A12-56 (VCP2) - Body ground
    10 kΩ or higher
    A6-2 (EPA2) or A12-58 (EPA2) - Body ground
    10 kΩ or higher
    A6-3 (VPA2) or A12-54 (VPA2) - Body ground
    10 kΩ or higher
    A6-4 (VCPA) or A12-55 (VCPA) - Body ground
    10 kΩ or higher
    A6-5 (EPA) or A12-57 (EPA) - Body ground
    10 kΩ or higher
    A6-6 (VPA) or A12-53 (VPA) - Body ground
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)

  1. A115666E04
    Disconnect the A6 accelerator pedal position sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A6-4 (VCPA) - A6-5 (EPA)
    4.5 to 5.5 V
    A6-1 (VCP2) - A6-2 (EPA2)
    4.5 to 5.5 V

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPLACE ECM
OK


4. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace the accelerator pedal rod assembly (Click here).


NEXT


5. CHECK IF OUTPUT DTC RECURS
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the engine at idle for 15 seconds or more.

  1. Read the DTC (Click here).

    Result:
    Display (DTC Output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127, P2128, or P2138 is output again
    A
    P2120, P2122, P2123, P2125, P2127, P2128, or P2138 is not output
    B



B
END
A

REPLACE ECM


← P2047 Reductant Injector Circuit / Open (Bank 1 Unit 1) (+ P2048, P2049) (from Jan 2007)P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (from Jan 2007) →