2005-2008 RAV4 · Service Manual ENGINE

P2047 Reductant Injector Circuit / Open (Bank 1 Unit 1)

Diagnostic trouble codes · Vehicles built from Jan 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

A114032E04
The exhaust fuel addition injector is mounted on the exhaust port of the cylinder head, and low pressure is provided to the injector by the feed pump in the supply pump. This injector adds fuel by a control signal from the ECM.
This injector is used for two different controls: DPNR catalyst regeneration and nitrogen oxide (NOx) reduction.
Under the DPNR catalyst regeneration control, the injector adds fuel to raise a catalyst temperature.
In the other control, the injector helps the air-fuel ratio become RICH. As a result, NOx in the exhaust gas will be reduced in response to the RICH air-fuel ratio.

HINT:
  1. For more information on the exhaust fuel addition injector and TOYOTA D-CAT*1, refer to the following procedures (Click here)
  2. If P2047, P2048 and P2049 are present, refer to the DTC table for TOYOTA D-CAT (Click here).
*1: Diesel Clean Advanced Technology.

DTC No.
DTC Detection Condition
Trouble Area
P2047
With the exhaust fuel addition injector off, the FIVM1 output is High and the FIVM2 output is Low for 3 seconds.
(1 trip detection logic)
  1. Open in exhaust fuel addition injector circuit
  2. Exhaust fuel addition injector
  3. ECM
P2048
With the exhaust fuel addition injector off, the FIVM1 output is High and the FIVM2 output is High for 0.16 seconds.
(1 trip detection logic)
P2049
With the exhaust fuel addition injector on, the FIVM1 output is Low and the FIVM2 output is Low for 7 or more times.
(1 trip detection logic)

HINT:
DTC P1386 (injector for exhaust fuel addition) will be present if there is an open malfunction in the exhaust fuel addition injector circuit.


MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVM) signals. The FIV signal is sent from the CPU to the (exhaust) fuel addition injector via a drive circuit inside the ECM. The FIVM signal, which is originally output from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVM signal, the ECM judges that the current has been applied to the (exhaust) fuel addition injector.
This DTC will be set if the ECM judges that the number of signals of the FIV and the FIVM are inconsistent.
A117827E02

WIRING DIAGRAM

Refer to DTC P1386 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. INSPECT EXHAUST FUEL ADDITION INJECTOR (RESISTANCE)
  1. Inspect exhaust fuel addition injector (Click here).



NG
REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
OK


2. CHECK WIRE HARNESS (EXHAUST FUEL ADDITION INJECTOR - ECM)

  1. A129658E01
    Disconnect the B52 exhaust fuel addition injector connector.

  1. Disconnect the B32 ECM connector.

  1. Check the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B52-1 - B32-105 (FIV)
    Below 1 Ω
    B52-2 - B32-109 (E1)
    Below 1 Ω
    B52-1 or B32-105 (FIV) - Body ground
    10 kΩ or higher

  1. Reconnect the exhaust fuel addition injector connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← P2047 Reductant Injector Circuit / Open (Bank 1 Unit 1) (+ P2048, P2049) (Nov 2005 – Dec 2006)P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (Nov 2005 – Dec 2006) →