P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007
Versions by build date: Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
- HINT:
- This is the repair procedure for the accelerator pedal position sensor.
- This electrical throttle system does not use a throttle cable.
- This accelerator pedal position sensor is a non-contact type.
- This is the repair procedure for the accelerator pedal position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting malfunctions. The ECM determines the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2121 |
Condition (a) continues for 2 seconds: (a) Difference between VPA1 and VPA2 exceeds the threshold (1 trip detection logic) |
|
WIRING DIAGRAM
Refer to DTC P2121 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. READ VALUE USING ACCELERATOR PEDAL POSITION SENSOR |
Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Position 1 and Accel Position 2.
Read the values.
- Standard voltage:
Accelerator Pedal
Accel Position 1
Accel Position 2
Released
0.6 to 1.0 V
1.4 to 1.8 V
Depressed
3.4 to 3.8 V
4.2 to 4.6 V
|
|
||||
| NG | |
| 2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
Disconnect the accelerator pedal position sensor connector.

Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
A6-1 (VCP2) - A12-56 (VCP2)
Below 1 Ω
A6-2 (EPA2) - A12-58 (EPA2)
Below 1 Ω
A6-3 (VPA2) - A12-54 (VPA2)
Below 1 Ω
A6-4 (VCPA) - A12-55 (VCPA)
Below 1 Ω
A6-5 (EPA) - A12-57 (EPA)
Below 1 Ω
A6-6 (VPA) - A12-53 (VPA)
Below 1 Ω
A6-1 (VCP2) or A12-56 (VCP2) - Body ground
10 kΩ or higher
A6-2 (EPA2) or A12-58 (EPA2) - Body ground
10 kΩ or higher
A6-3 (VPA2) or A12-54 (VPA2) - Body ground
10 kΩ or higher
A6-4 (VCPA) or A12-55 (VCPA) - Body ground
10 kΩ or higher
A6-5 (EPA) or A12-57 (EPA) - Body ground
10 kΩ or higher
A6-6 (VPA) or A12-53 (VPA) - Body ground
10 kΩ or higher
Reconnect the accelerator pedal position sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
