2005-2008 RAV4 · Service Manual ENGINE

P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Jan 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

HINT:
  1. For more information on the A/F sensor and TOYOTA D-CAT*, refer to the following procedures (Click here).
  2. These DTCs are related to the A/F sensor, although the titles say oxygen sensor.
  3. If P2237, P2238 and/or P2239 is present, refer to the DTC table for TOYOTA D-CAT system (Click here).
  4. These DTCs are recorded when A/F sensor has malfunction, although the titles say oxygen sensor.
*: Diesel Clean Advanced Technology.

The A/F sensor has the characteristic of providing output voltage which is proportional to the existing air- fuel ratio. The A/F sensor output voltage*1 is used to provide the ECM with feedback to control the air-fuel ratio.
The A/F sensor is located after the DPNR*2 catalytic converter. This sensor has been developed based on the structure and technology of the sensor used for gasoline engines. The cover portion of the sensor has been changed for use in the diesel engine with TOYOTA D-CAT in order to eliminate the influence of the sensor temperature and particulate matter (PM).
In order to reduce both PM and nitrogen oxides (NOx), the ECM adjusts the air-fuel ratio to slightly RICH (LEAN compared with a stoichiometric air-fuel ratio) based on signals from the A/F sensor. When the ECM exercises DPNR catalyst regeneration by adding fuel using the exhaust fuel addition injector, the air-fuel ratio is also properly adjusted through the sensor.
*1: The voltage value changes inside the ECM only.
*2: Diesel Particulate-NOx Reduction system.
A107164E09

HINT:
The ECM provides a pulse width modulated control circuit to adjust current through the heater. The A/F sensor heater circuit uses a relay on the B+ side of the circuit.

A128583E01
DTC No.
DTC Detection Condition
Trouble Area
P2237
ECM internal error (5.0 seconds)
(1 trip detection logic)
ECM
P2238
P2252
A/F sensor circuit low (bank 1 sensor 1)
AF+ is less than 1.0 V for 5.0 seconds or more
(1 trip detection logic)
Main trouble area: Open in A/F sensor circuit
  1. Open or short in A/F sensor circuit
  2. A/F sensor
  3. A/F sensor heater
  4. A/F sensor heater relay
  5. A/F sensor heater and relay circuit
  6. ECM
P2239
P2253
A/F sensor circuit high (bank 1 sensor 1)
AF+ is more than 4.0 V for 5.0 seconds or more
(1 trip detection logic)
Main trouble area: Short in A/F sensor circuit
  1. Open or short in A/F sensor circuit
  2. A/F sensor
  3. A/F sensor heater
  4. A/F sensor heater relay
  5. A/F sensor heater and relay circuit
  6. ECM

MONITOR DESCRIPTION

The A/F sensor varies its voltage output in proportion to the air-fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the A/F sensor circuit.

WIRING DIAGRAM

Refer to DTC P0031 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2237)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P2237 and P2238, P2239, P2252 and/or P2253
    A
    P2237
    B



B
REPLACE ECM
A


2. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

  1. C128155E02
    Disconnect the B62 A/F sensor connector.

  1. Measure the resistance of the terminals of the A/F sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B62-1 (HAF2) - B62-2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR
OK


3. INSPECT INTEGRATION RELAY (A/F RELAY)
A107921E15
  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Inspect the A/F fuse.

    1. Remove the A/F fuse from the integration relay.

    2. Measure the resistance of the fuse.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the A/F fuse.

  1. Inspect the A/F relay.

    1. Measure the A/F relay resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      1B-8 - 1C-1
      10 kΩ or higher
      1B-8 - 1C-1
      Below 1 Ω (Apply battery voltage to terminals 1B-6 and 1B-7)

    2. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


4. CHECK WIRE HARNESS (A/F SENSOR - ECM)
A128584E01
  1. Disconnect the B62 A/F sensor connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    B62-1 (HAF2) - B32-104 (HAF2)
    Below 1 Ω
    B62-1 (HAF2) or B32-104 (HAF2) - Body ground
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) (+ P2238, P2239, P2252, P2253) (Nov 2005 – Dec 2006)Engine Difficult to Start or Stalling (Nov 2005 – Dec 2006) →