2005-2008 RAV4 · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL SHIFT FORK SHAFT BEARING

  1. C116725E02
    Using SST and a press, press the needle roller bearing into the control shaft cover.
    SST
    09285-76010  

    Standard depth:
    1.0 to 1.5 mm (0.039 to 0.059 in.)


2. INSTALL CONTROL SHAFT COVER OIL SEAL

  1. C112481E02
    Using SST and a hammer, tap a new oil seal into the control shaft cover.
    SST
    09307-12010  

    Standard depth:
    0 to 0.5 mm (0 to 0.020 in.)

  1. Coat the lip of the oil seal with MP grease.


3. INSTALL SHIFT LEVER DAMPER

  1. C115448
    Coat the 2 bolts with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344, or equivalent

  1. Install the shift lever damper to the shift and select lever shaft with the bolts.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


4. INSTALL PIN

  1. C118049
    Install the 2 pins to the No. 1 shift lever inner.


5. INSTALL SHIFT GATE PLATE

  1. C116727E05
    Install the shift gate plate with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }


6. INSTALL SHIFT AND SELECT LEVER SHAFT

  1. C112483
    Install the shift and select lever boot and the shift control cover into the select lever shaft.


7. INSTALL NO. 1 SHIFT LEVER INNER

  1. C112482
    Install the No. 1 shift lever inner and the shift interlock plate onto the shift and select lever shaft.

  1. C118050
    Using a pin punch and hammer, tap the slotted spring pin into the No. 1 shift lever inner.

    Standard depth:
    0.4 to 1.4 mm (0.016 to 0.055 in.)


8. INSTALL CONTROL SHAFT COVER

  1. C113551E02
    Align the 4 shift fork shafts as shown in the illustration.

  1. C113550E03
    Apply Toyota genuine seal packing black to the manual transmission case, as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing black 1281, THREE BOND 1281 or equivalent

  1. Coat the 4 bolts with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

  1. C112484
    Install the shift and select lever shaft onto the transmission case with the 4 bolts.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


9. INSTALL SHIFT GATE PIN

  1. C116598
    Coat the shift gate pin with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

  1. Install the shift gate pin onto the transmission case.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


10. INSTALL NO. 2 LOCK BALL ASSEMBLY

  1. C116561
    Coat the lock ball with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

  1. Install the lock ball onto the transmission case.

    Torque:
    29 N*m{ 299 kgf*cm , 22 ft.*lbf }


11. INSTALL NO. 1 LOCK BALL ASSEMBLY

  1. C116559
    Coat the lock ball with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

  1. Install the lock ball onto the transmission case.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


12. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

  1. C112472E03
    Install the back-up light switch onto the transmission case.
    SST
    09816-30010  

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }


13. INSTALL NO. 1 SELECTING BELLCRANK DUST COVER

  1. C116207
    Install the dust cover onto the selecting bellcrank.


14. INSTALL CONTROL SHIFT LEVER BUSH

  1. C113636
    Install the control shift lever bush to the selecting bellcrank.


15. INSTALL SELECTING BELL CRANK ASSEMBLY

  1. C112480
    Coat the 2 bolts with sealant, and install the selecting bell crank to the transmission case with the bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

← DISASSEMBLY (from Nov 2005)COMPONENTS (from Nov 2005) →