2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL CYLINDER HEAD GASKET

  1. A126929E01
    Place a new gasket on the cylinder block surface with the Lot No. stamp facing upward.

    NOTICE:
    1. Remove any oil from contact surface.
    1. Be careful of the installation direction.


2. INSTALL CYLINDER HEAD SUB-ASSEMBLY
  1. Place the cylinder head on the head gasket.

    NOTICE:
    Place the cylinder head gently in order to avoid damaging the gasket.

  1. Install the cylinder head bolts.

    NOTICE:
    The cylinder head bolts are tightened in 2 successive steps.


    1. F050595E03
      Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.

    2. Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration.

      Torque:
      78.5 N*m{ 800 kgf*cm , 58 ft.*lbf }

  1. A098364E01
    Mark the front of the cylinder head bolts with paint.

  1. Retighten the cylinder head bolts by 90°as shown in the illustration.

  1. Check that the paint mark is now at a 90°angle to the front.


3. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

  1. A098365E02
    Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.

  1. Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

    NOTICE:
    Be sure not to turn the camshaft timing gear to the retard angle side (the right angle).

  1. Check that there is no clearance between the gear fringe and camshaft.

  1. Tighten the flange bolt with the camshaft timing gear fixed in place.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.


4. INSTALL NO. 2 CAMSHAFT TIMING SPROCKET

  1. A032167E01
    Clamp the camshaft in a vise, then install the camshaft timing sprocket with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    NOTICE:
    Do not damage the camshaft.


5. INSTALL CAMSHAFT
  1. Apply a light coat of engine oil to the journal portion of the camshaft.

  1. F050592E01
    Place the 2 camshafts on the cylinder head with the No. 1 cam lobes facing the directions shown in the illustration.

  1. F050591E01
    Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. F050596E02
    Using several steps, uniformly tighten the 20 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    29.5 N*m{ 301 kgf*cm , 22 ft.*lbf } for No. 1 and No. 2 bearing cap
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for No. 3 bearing cap

    NOTICE:
    1. Tighten the bolts after deciding the position in the thrust direction of the camshaft by the No. 1 and No. 2 bearing caps.
    1. Install the camshaft with the timing mark of the camshaft timing gear on top.


6. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  1. A132570
    Install the chain vibration damper with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


7. INSTALL CHAIN SUB-ASSEMBLY

  1. A098367E01
    Set the No. 1 cylinder to TDC/compression.

    1. Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.

    2. A052505E01
      Using the crankshaft pulley bolt, turn the crankshaft to position the key on the crankshaft upward.

  1. A094576E01
    Install the chain onto the crankshaft timing sprocket with the gold or orange mark link aligned with the timing mark on the crankshaft.

  1. A098369E01
    Using SST and a hammer, tap in the crankshaft timing sprocket.
    SST
    09309-37010  

  1. A098370E01
    Align the gold or yellow links with each timing mark located on the camshaft timing gear and sprocket, then install the chain.


8. INSTALL CHAIN TENSIONER SLIPPER

  1. A124787E01
    Install the chain tensioner slipper with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


9. INSTALL TIMING CHAIN GUIDE

  1. A077243E01
    Install the timing chain guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


10. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A124770
    Install the sensor plate with the "F" mark facing forward.


11. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

  1. A094577E01
    Apply seal packing (Diameter 4.0 to 4.5 mm (0.157 to 0.177 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the chain cover within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the chain cover.

  1. Apply a continuous bead of seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the chain cover within 3 minutes of applying seal packing.

    1. Do not add engine oil for at least 2 hours after installing the chain cover.

      A132566E02

  1. A132568E03
    Install the timing chain cover with the 12 bolts and 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt A
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } for bolt B
    55 N*m{ 561 kgf*cm , 41 ft.*lbf } for bolt C
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for nut

    HINT:
    Bolt length:
    Bolt A
    30 mm (1.18 in.) length for 10 mm head
    Bolt B
    30 mm (1.18 in.) length for 12 mm head
    Bolt C
    40 mm (1.57 in.) length for 14 mm head

  1. A014253E03
    Using an E10 "torx" socket, install the stud bolt for the V-ribbed belt tensioner.

    Torque:
    21.5 N*m{ 219 kgf*cm , 16 ft.*lbf }


12. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A098376E03
    Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.

  1. A098377E03
    Install a new gasket and the chain tensioner with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    When installing the chain tensioner, set the hook again if the hook releases the plunger.


13. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A112212
    Install the V-ribbed belt tensioner with the bolt and nut.

    Torque:
    59.5 N*m{ 607 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Do not lift the engine more than necessary.


14. INSTALL ENGINE MOUNTING BRACKET RH

  1. A128165
    Install the engine mounting bracket RH with the 3 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }


15. INSTALL CRANKSHAFT PULLEY

  1. A098346E01
    Using SST, fix the pulley in place and tighten the bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    180 N*m{ 1,835 kgf*cm , 133 ft.*lbf }

  1. A112204E02
    Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.

  1. A112205E02
    Turn the crankshaft clockwise, then check that the plunger is extended.


16. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.

  1. A114332E01
    Apply a continuous bead of seal packing (Diameter 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the oil pan within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the oil pan.

  1. Install the oil pan to the cylinder block.

  1. A114333E01
    Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A061184E04
    Place a transmission jack underneath the engine, then put a wooden block on the jack.

  1. Remove the chain block and sling device.

  1. Remove the No. 1 and No. 2 engine hangers.


17. INSTALL CRANKSHAFT POSITION SENSOR

A095436E01

NOTICE:
Make sure that the O-ring is not cracked or jammed when installing it.

  1. Apply a light coat of engine oil to the O-ring of the sensor.

  1. A116845E01
    Install the sensor with the bolt.

    Torque:
    9.0 N*m{ 90 kgf*cm , 80 in.*lbf }

  1. Install the wire harness clamp.

  1. Install the connector clamp.

  1. Connect the sensor connector.

  1. Confirm that the wire harness of the sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover.


18. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing material from the contact surface.

  1. A094205E01
    Apply seal packing to the 2 locations shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the oil pan within 3 minutes of applying seal packing.
    1. Do not add engine oil for at least 2 hours after installing the oil pan.

  1. A094204E01
    Install the cylinder head cover with the 8 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for bolt A
    14 N*m{ 143 kgf*cm , 10 ft.*lbf } for bolt B
    11 N*m{ 112 kgf*cm , 8 ft.*lbf } for nut

  1. A112210
    Install the 2 engine wires with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Connect the clamp of the engine wire (labeled B).

  1. A112209
    Connect the 2 ventilation hoses to the cylinder head cover.


19. INSTALL IGNITION COIL ASSEMBLY

  1. A124400
    Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the 4 ignition coil connectors.


20. INSTALL IDLER PULLEY

  1. A132481
    Install the idler bracket with the 2 bolts.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }


21. INSTALL ENGINE MOUNTING INSULATOR RH

  1. A124843E01
    Install the engine mounting insulator RH with the 4 bolts and 2 nuts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf } for bolt
    95 N*m{ 969 kgf*cm , 70 ft.*lbf } for nut A
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for nut B

  1. A098189E01
    Connect the 2 clamps of the engine wire.

  1. Install the wire harness protector with the bolt.


22. INSTALL RADIATOR RESERVOIR

  1. A124838
    Install the reservoir with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


23. INSTALL GENERATOR ASSEMBLY

  1. A097394E02
    Confirm that the wire harness of the crankshaft position sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover.

  1. A122810E01
    Install the generator with the 2 bolts.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf } for bolt A
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for bolt B

  1. A122809
    Install the wire harness clamp.

  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Install the terminal cap.

  1. Connect the generator connector.


24. INSTALL FAN AND GENERATOR V BELT

  1. A114351E01
    Using SST and 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then install the fan and generator V belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply force any more than necessary.


25. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH
  1. Install the reinforcement RH with the 4 bolts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }


26. CONNECT ENGINE WIRE

  1. A098748E01
    Connect the ground cable with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Connect the camshaft position sensor connector.

  1. Connect the engine coolant temperature sensor connector.

  1. Connect the engine oil pressure switch connector.

  1. Connect the radio setting condenser connector.

  1. Connect the heater water inlet hose.


27. CONNECT NO. 1 RADIATOR HOSE

  1. A114348
    Connect the hose to the cylinder head.


28. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A090053E01
    Apply a light coat of engine oil to the O-ring of the oil control valve.

  1. A124556
    Install the oil control valve with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    Make sure that the O-ring is not cracked or jammed.

  1. Connect the oil control valve connector.


29. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
  1. Install a new gasket onto the cylinder head.

  1. Temporarily tighten the exhaust manifold converter with the 5 nuts.

  1. A112190E01
    Tighten the 5 nuts in the sequence shown in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


30. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A112189
    Install the exhaust manifold heat insulator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. A098744E01
    Connect the air-fuel ratio sensor connector.


31. INSTALL NO. 2 MANIFOLD STAY

  1. A112192
    Install the stay with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


32. INSTALL MANIFOLD STAY

  1. A112193
    Install the stay with the bolt and nut.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


33. INSTALL FRONT EXHAUST PIPE

  1. A077857E03
    Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    41.5 mm (1.634 in.)

    If the length is less than the minimum, replace the compression spring.

  1. A133205E01
    Install a new gasket by hand so that its surface is flush with the exhaust manifold.

    NOTICE:
    1. Make sure the gasket is facing the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the front exhaust pipe.

  1. Install the front exhaust pipe with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    A126831


34. INSTALL OIL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring and install it onto the guide.

  1. A112218E01
    Install the guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


35. INSTALL OIL DIPSTICK

36. INSTALL INTAKE MANIFOLD INSULATOR

  1. A095425E02
    Install the intake manifold insulator onto the cylinder block.


37. INSTALL INTAKE MANIFOLD

  1. A090130E02
    Install a new gasket into the intake manifold.

  1. A125028
    Install the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    30 N*m{ 305 kgf*cm , 22 ft.*lbf }

  1. Fit the union to check valve hose into the vacuum hose clamp.

  1. Install the wire harness clamp.

  1. Connect the camshaft timing oil control valve connector.

  1. Connect the union to check valve hose to the brake booster.


38. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A125335
    Install 4 new insulators into the cylinder head.

  1. Install the 2 delivery pipe spacers onto the cylinder head.

  1. A097444E02
    Install the fuel delivery pipe together with the 4 fuel injectors, then temporarily tighten the 2 bolts.

    NOTICE:
    Be careful not to drop the fuel injectors when installing the fuel delivery pipe.

  1. Check that the fuel injector rotates smoothly.
    If the fuel injector does not rotate, replace the O-ring.

  1. A125334
    Tighten the 2 bolts to the specified torque.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }

  1. A125333
    Connect the 4 fuel injector connectors.

  1. Install the 2 wire harness clamps.


39. INSTALL THROTTLE BODY

  1. A124566
    Install a new gasket onto the intake manifold.

  1. A124565
    Install the throttle body and fuel pipe clamp with the 4 bolts.

    Torque:
    30 N*m{ 305 kgf*cm , 22 ft.*lbf }

  1. A124564
    Connect the fuel tube into the clamp.

  1. Connect the wire harness clamp.

  1. Connect the throttle position sensor and control motor connector.

  1. Connect the No. 1 throttle body hose to the throttle body.

  1. Connect the No. 2 water by-pass hose to the throttle body.

  1. Connect the water by-pass hose to the throttle body.

  1. Connect the purge line hose to the throttle body.


40. INSTALL AIR CLEANER CAP
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A124568E01
    Insert the hinge part of the air cleaner cap into the air cleaner case, then hang the 2 hook clamps.

  1. A124569E01
    Align the matchmarks of the No. 1 air cleaner hose and throttle body, and then connect the air cleaner hose No. 1 to the throttle body and unfasten the No. 1 air cleaner hose clamp.

    NOTICE:
    Make sure that the hose clamp is at the correct angle.

  1. A124560
    Connect the purge line hose to the clamp.

  1. Connect the No. 2 ventilation hose to the air cleaner hose.

  1. A124559
    Install the 4 wire harness clamps.

  1. Connect the mass air flow meter connector.


41. ADD ENGINE OIL
  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Add new oil.

    Standard capacity:
    Item
    Standard Condition
    Drain and refill with oil filter change
    4.3 liters (4.5 US qts, 3.8 Imp. qts)
    Drain and refill without oil filter change
    4.1 liters (4.3 US qts, 3.6 Imp. qts)
    Dry fill
    5.0 liters (5.3 US qts, 4.4 Imp. qts)

  1. Install the oil filler cap.


42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

43. CHECK FOR FUEL LEAKS

44. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    12.7 N*m{ 130 kgf*cm , 10 ft.*lbf }

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.

  1. A112307E01
    Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir's filler neck.

    HINT:
    The B line is the lower edge of the inner wall of the filler neck.

    Standard capacity:
    Item
    Specified Condition
    A/T
    6.5 liters (6.9 US qts, 5.7 Imp. qts)
    M/T
    6.6 liters (7.0 US qts, 5.9 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. Start the engine and warm it up until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Specified Condition
      Manual Air Conditioning System
      Fan speed: Any setting except OFF
      Temperature: Toward WARM
      Air conditioning switch: OFF
      Automatic Air Conditioning System
      Temperature: Toward MAX
      Air conditioning switch: OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.
      4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
      5. Run the engine at 2,000 rpm until the coolant level has stabilized.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

  1. A112306
    Check that the coolant level is between the FULL and LOW line.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.


45. CHECK FOR ENGINE COOLANT LEAKS
  1. Check for engine coolant leaks (Click here).


46. CHECK FOR ENGINE OIL LEAKS

47. CHECK FOR EXHAUST GAS LEAKS

48. CHECK IGNITION TIMING

NOTICE:
  1. Turn all the electrical systems and the A/C OFF.
  2. Inspect the ignition timing with the cooling fan OFF.
  3. When checking the ignition timing, shift the transmission to the neutral position.

  1. Warm up and stop the engine.

  1. B127990E01
    When using intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Allow the engine to idle.

    3. Select the following menu items:
      Powertrain / Engine and ECT / Data List / IGN Advance.

    4. Read IGN Advance to check the ignition timing.

      Standard ignition timing:
      5 to 15° BTDC @ idle

    5. Check that the ignition timing advances immediately when the engine speed is increased.

    6. Turn the ignition switch off.

    7. Disconnect the intelligent tester from the DLC3.

  1. When not using intelligent tester:

    1. Remove the No. 1 engine cover (Click here).

    2. A112264
      Open the ignition cover located in the right of the No. 4 ignition coil.

    3. Pull out the wire harness from the IG cover.

    4. Connect the timing light to the wire harness.

      NOTICE:
      Use a timing light that detects the first signal.

    5. H100769E05
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

    6. Allow the engine to idle and check the ignition timing.

      Standard ignition timing:
      8 to 12° BTDC @ idle

      HINT:
      Run the engine at 1,000 to 1,300 rpm for 5 seconds, then check that the engine speed returns to the idling speed.

    7. Remove SST from the DLC3.

    8. Allow the engine to idle and check the ignition timing.

      Standard ignition timing:
      5 to 15° BTDC

    9. Check that the ignition timing advances immediately when the engine speed is increased.

    10. Turn the ignition switch off.

    11. Remove the timing light.

    12. Close the IG cover.

    13. Install the No. 1 engine cover (Click here).


49. INSPECT ENGINE IDLING SPEED

  1. B127990E01
    When using intelligent tester:

    1. Turn OFF all the accessories and air conditioning.

    2. Move the shift lever to P or neutral.

    3. Connect the intelligent tester to the DLC3.

    4. Warm up the engine.

    5. Select the tester menus:
      Powertrain / Engine and ECT / Data List / Engine SPD.

    6. Read Engine SPD to check the idle speed while the radiator-cooling fan is not rotating.

      Standard idle speed:
      Item
      Specified Condition
      A/T
      600 to 700 rpm
      M/T
      600 to 700 rpm

    7. Turn the ignition switch off.

    8. Disconnect the tester from the DLC3.

  1. When not using intelligent tester:

    1. Turn OFF all the accessories and air conditioning.

    2. Move the shift lever to P or neutral.

    3. H100769E32
      Connect SST to 9 (TAC) of the DLC3 terminal, and then connect a tachometer to SST.
      SST
      09843-18030  

    4. Warm up the engine.

    5. Check the idle speed while the radiator-cooling fan is not rotating.

      Standard idle speed:
      Item
      Specified Condition
      A/T
      600 to 700 rpm
      M/T
      600 to 700 rpm

    6. Turn the ignition switch off.

    7. Remove the tachometer and disconnect SST from the DLC3.


50. INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the No. 1 engine under cover.

  1. Remove the 4 ignition coils (Click here).

  1. Remove the 4 spark plugs.

  1. Disconnect the 4 fuel injector connectors.

  1. A013304E05
    Set SST and a compression gauge.
    SST
    09992-00500  

  1. Insert the compression gauge into the spark plug hole.

  1. While cranking the engine, measure the compression pressure.

    Standard compression pressure:
    1,300 kPa (13.8 kgf/cm2, 196 psi)

    Minimum pressure:
    1,000 kPa (10 kgf/cm2, 142 psi)

    Standard difference between each cylinder:
    100 kPa (1.0 kgf/cm2, 14 psi)

    NOTICE:
    1. Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
    2. Check the other cylinder's compression pressures in the same way.
    3. This measurement must be done as quickly as possible.

    If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.

    HINT:
    1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
    2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.

  1. Connect the 4 fuel injector connectors.

  1. Install the 4 spark plugs.

  1. Install the 4 ignition coils (Click here).

  1. Install the No. 1 engine under cover.


51. INSPECT CO/HC

HINT:
The ECM properly controls the CO/HC concentration in the emission gas.

  1. Start and warm up the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.

  1. Inspect the CO/HC concentration while idling and/or at 2,500 rpm.
    If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.

    1. See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idle
      1. Faulty ignition:
      - Incorrect timing
      - Plugs are contaminated, shorted, or gaps are defective
      2. Incorrect valve clearance
      3. Leaks in intake and exhaust valve
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leakage:
      - Ventilation hoses
      - Intake manifold
      - Throttle body
      - Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
      - Faulty pressure regulator
      - Faulty engine coolant temperature sensor
      - Faulty mass air flow meter
      - Faulty ECM
      - Faulty injectors
      - Faulty throttle body


52. INSTALL NO. 1 ENGINE COVER

  1. A112206
    Install the engine cover with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


53. INSTALL FRONT FENDER APRON RH

54. INSTALL NO. 1 ENGINE UNDER COVER

55. INSTALL FRONT WHEEL RH

56. INSTALL RADIATOR SUPPORT OPENING COVER
← INSTALLATION (Jan 2007 – Jul 2007)REPAIR (from Nov 2005) →