2005-2008 RAV4 · Service Manual BRAKE

Brake Warning Light Remains ON

Circuit diagnosis · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

If any of the following conditions are detected, the brake warning light remains on:
  1. The ECU connectors are disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. The EBD is defective.

WIRING DIAGRAM

C131831E01
C131832E01

INSPECTION PROCEDURE


1. PREPARE FOR INSPECTION
  1. Check that both of the following conditions are satisfied.

    1. The brake fluid level in the brake master cylinder reservoir is correct.
    2. The parking brake is released.

    HINT:
    When the ABS warning light remains illuminated, repair the malfunctions in the ABS system first.


NEXT


2. CHECK DTC FOR ABS
  1. Check if any ABS DTCs are output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


3. CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication system DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CAN COMMUNICATION SYSTEM
A


4. INSPECT SKID CONTROL ECU CONNECTOR
  1. Check if the skid control ECU connector is properly installed.

    OK:
    The skid control ECU connector is properly installed.



NG
CONNECT CONNECTOR TO ECU SECURELY
OK


5. CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)

  1. C117862E11
    Disconnect the A27 ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A27-2 (GND1) - Body ground
    Below 1 Ω
    A27-24 (GND2) - Body ground
    Below 1 Ω

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A27-25 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6. READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH)
  1. Using the Data List, check for proper functioning of the parking brake switch.

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released

    OK:
    When the parking brake lever is operated, the display changes as shown above.



NG
Go to step 10
OK


7. INSPECT BRAKE FLUID LEVEL WARNING SWITCH

  1. C126315
    Remove the reservoir tank cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance of the switch.

    HINT:
    A float is placed inside the reservoir. Its position can be changed by increasing or decreasing the brake fluid level.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float up (Switch OFF)
    10 kΩ or higher
    1 - 2
    Float down (Switch ON)
    Below 1 Ω

    HINT:
    If there is no problem after the above check is finished, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
OK


8. CHECK WIRE HARNESS (COMBINATION METER - LEVEL WARNING SWITCH AND BODY GROUND)

  1. C126282E01
    Disconnect the E22 combination meter connector.

  1. Disconnect the A10 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E22-14 (SW) - A10-1
    Below 1 Ω
    E22-14 (SW) - Body ground
    10 kΩ or higher
    A10-2 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


9. CHECK COMBINATION METER
  1. Check the combination meter (Click here).



NG
REPLACE COMBINATION METER
OK

REPLACE BRAKE ACTUATOR ASSEMBLY

10. INSPECT PARKING BRAKE SWITCH ASSEMBLY

  1. C118703E03
    Remove the parking brake switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin not pushed)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY
OK


11. CHECK WIRE HARNESS (JUNCTION BLOCK - PARKING BRAKE SWITCH AND BODY GROUND)

  1. C126283E01
    Disconnect the ID junction block connector.

  1. Disconnect the E46 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    ID-4 (PKB) - E46-1
    Below 1 Ω
    ID-4 (PKB) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)


← Brake Warning Light Remains ON (Jan 2007 – Jul 2007)Brake Warning Light does not Come ON (Nov 2005 – Dec 2006) →