INSTALLATION
Removal / installation · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
- CAUTION:
- Be sure to read the precautionary notices concerning the SRS airbag system before servicing it (Click here).
| 1.
INSTALL AIRBAG SENSOR REAR LH |
 |
- Install the airbag sensor with the bolt.
-
Torque:
- 9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
- NOTICE:
- If the airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
- When installing the airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
| 2.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)
|
 |
Install the belt hanger to the trim board.
Connect the power outlet socket connector.
Attach the 5 clips and 5 claws to install the trim board.
Install the bolt and 2 screws.
- Connect the rear No.1 seat belt's floor anchor.
Connect the floor anchor with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Install the anchor cover.
| 3.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)
|
 |
- Install the belt hanger to the trim board.
Connect the power outlet socket connector.
Attach the 4 clips and 5 claws to install the trim board.
Install the 2 screws and 2 bolts.
- Connect the rear No.1 seat belt's floor anchor.
Connect the floor anchor with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Install the anchor cover.
| 4.
CONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH
|
 |
Connect the seat belt's floor anchor with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Attach the lap belt outer anchor cover.
| 5.
INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET |
|
| 6.
INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER |
|
| 7.
INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH |
|
| 8.
INSTALL REAR FLOOR FINISH PLATE (for Short Body)
|
 |
- Attach the 6 clips to install the finish plate.
| 9.
INSTALL REAR FLOOR FINISH PLATE (for Long Body)
|
 |
- Attach the 2 claws and 6 clips to install the finish plate.
| 10.
INSTALL BACK DOOR WEATHERSTRIP |
|
| 11.
INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
|
 |
Attach the 7 clips to install the side plate.
Install the 4 screws.
| 12.
INSTALL JACK CARRIER ASSEMBLY (for Short Body)
|
 |
- Install the jack carrier with the 7 clips.
| 13.
INSTALL REAR FLOOR NO. 3 BOARD |
|
| 14.
INSTALL REAR FLOOR NO. 2 BOARD |
|
| 15.
INSTALL DECK BOARD ASSEMBLY |
|
| 16.
INSTALL REAR FLOOR NO. 1 BOARD |
|
| 17.
INSTALL TONNEAU COVER ASSEMBLY |
|
| 18.
INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY |
|
| 19.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
|
| 20.
INSTALL REAR DOOR SCUFF PLATE LH (for Short Body)
|
 |
- Attach the 8 claws to install the scuff plate.
| 21.
INSTALL REAR DOOR SCUFF PLATE LH (for Long Body)
|
 |
- Attach the 9 claws and 2 clips to install the scuff plate.
| 22.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
|
| 23.
CHECK SRS WARNING LIGHT |
 |
Check the SRS warning light (Click here).