2005-2008 RAV4 · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.

CAUTION:
Be sure to read the precautionary notices concerning the SRS airbag system before servicing it (Click here).


1. INSTALL AIRBAG SENSOR REAR LH

  1. B127923E01
    Install the airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.


2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)

B129712
  1. Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 5 clips and 5 claws to install the trim board.

  1. Install the bolt and 2 screws.

  1. B137546
    Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.


3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)

  1. B129706
    Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 4 clips and 5 claws to install the trim board.

  1. Install the 2 screws and 2 bolts.

  1. B137546
    Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.


4. CONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH

B133643
  1. Connect the seat belt's floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Attach the lap belt outer anchor cover.


5. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET

6. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER

7. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH

8. INSTALL REAR FLOOR FINISH PLATE (for Short Body)

  1. B129716
    Attach the 6 clips to install the finish plate.


9. INSTALL REAR FLOOR FINISH PLATE (for Long Body)

  1. B129704
    Attach the 2 claws and 6 clips to install the finish plate.


10. INSTALL BACK DOOR WEATHERSTRIP

11. INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE

B129717
  1. Attach the 7 clips to install the side plate.

  1. Install the 4 screws.


12. INSTALL JACK CARRIER ASSEMBLY (for Short Body)

  1. B129715
    Install the jack carrier with the 7 clips.


13. INSTALL REAR FLOOR NO. 3 BOARD

14. INSTALL REAR FLOOR NO. 2 BOARD

15. INSTALL DECK BOARD ASSEMBLY

16. INSTALL REAR FLOOR NO. 1 BOARD

17. INSTALL TONNEAU COVER ASSEMBLY

18. INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY

19. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

20. INSTALL REAR DOOR SCUFF PLATE LH (for Short Body)

  1. B129711
    Attach the 8 claws to install the scuff plate.


21. INSTALL REAR DOOR SCUFF PLATE LH (for Long Body)

  1. B129703
    Attach the 9 claws and 2 clips to install the scuff plate.


22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

23. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← INSTALLATION (Jan 2007 – Jul 2007)COMPONENTS (from Nov 2005) →