2005-2008 RAV4 · Service Manual HEATER & AIR CONDITIONING SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Jul 2007 from Aug 2007


CHECK AIR CONDITIONING AMPLIFIER
E123551E01
  1. Measure the voltage of the connectors.

    HINT:
    Check from the rear of the connector while it is connected to the air conditioning amplifier.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    LOCK (E42-3) - SG-2 (E42-10) (*2)
    W - G
    Compressor lock sensor signal
    Ignition switch on (IG)
    AUTO switch ON
    A/C switch ON
    Magnetic clutch ON
    Pulse generation
    (see waveform 4)
    S5-3 (E42-7) - GND (E42-24)
    B - W-B
    Power supply for pressure sensor
    Ignition switch on (IG)
    4.5 to 5.5 V
    CANH (E42-8) - GND (E42-24)
    V - W-B
    Hi-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 1)
    CANL (E42-9) - GND (E42-24)
    W - W-B
    Lo-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    SG-2 (E42-10) - Body ground
    G - Body ground
    Ground for pressure sensor
    Always
    Below 1 V
    PRE (E42-12) - SG-2 (E42-10)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: normal
    0.76 to 4.74 V
    PRE (E42-12) - SG-2 (E42-10)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi]
    Below 0.76 V
    PRE (E42-12) - SG-2 (E42-10)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi])
    4.74 V or more
    SOL+ (E42-13) - GND (E42-24)
    GR - W-B
    A/C compressor operation signal
    Engine idling
    Pulse generation
    (see waveform 3)
    Heater control (blower switch): 1
    A/C switch ON
    IG+ (E42-14) - GND (E42-24)
    Y - W-B
    Power source (IG)
    Ignition switch on (IG)
    10 to 14 V
    MGC (E42-15) - GND (E42-24) (*2)
    V - W-B
    Magnetic clutch relay signal
    Ignition switch on (IG)
    Magnetic clutch OFF
    10 to14 V
    MGC (E42-15) - GND (E42-24) (*2)
    V - W-B
    Magnetic clutch relay signal
    Ignition switch on (IG)
    Magnetic clutch ON
    Below 1.5 V
    SBLW (E42-21) - GND (E42-24)
    GR - W-B
    Blower motor ON signal
    Ignition switch on (IG)
    10 to 14 V → Below 1 V
    Heater control (blower switch): 0 → 1
    TE (E42-22) - SG-3 (E42-23)
    W - B
    Evaporator temperature sensor signal
    Ignition switch on (IG)
    1 to 1.3 V
    Temperature near evaporator: 15°C (59°F)
    SG-3 (E42-23) - Body ground
    B - Body ground
    Ground for evaporator temperature sensor
    Always
    Below 1 V
    GND (E42-24) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 V
    A/C (E42-27) - GND (E42-24)
    P - W-B
    A/C switch signal
    Ignition switch on (IG)
    Below 1 V → 10 to 14 V
    A/C switch OFF → ON
    LED (E42-28) - Body ground
    GR - Body ground
    A/C switch indicator signal
    Engine idling
    10 to 14 V → Below 4 V
    A/C switch ON
    Heater control (blower switch): 0 → 1
    B (E43-1) - GND (E42-24) (*1)
    R - W-B
    Power source (Back-up)
    Always
    10 to 14 V
    PTC1 (E43-9) - GND (E42-24) (*1)
    W - W-B
    PTC NO. 1 heater relay operation signal
    Engine idling
    Below 1 V → 10 to 14 V
    Air mix control knob: Max hot
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Light control switch: OFF
    Heater control (blower switch): 0 → 1
    Waiting time: 10 seconds
    PTC2 (E43-10) - GND (E42-24) (*1)
    B - W-B
    PTC NO. 2 heater relay operation signal
    Engine idling
    Below 1 V → 10 to 14 V
    Air mix control knob: Max hot
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Light control switch: OFF
    Heater control (blower switch): 0 → 1
    Waiting time: 20 seconds
    HEAT (E43-14) - Body ground (*1)
    W - Body ground
    MAX HOT switch detection signal
    Ignition switch on (IG)
    10 to 14 V
    Air mix control knob: Max hot
    Heater control (blower switch): 1
    HLS (E43-23) - Body ground (*1)
    BR - Body ground
    Headlight control signal
    Engine idling
    Below 1 V
    Light control switch: head position
    ALT (E43-24) - GND (E42-24) (*1)
    B - W-B
    Generator operation signal
    Engine idling
    Pulse generation

    HINT:
    *1: w/ PTC heater
    *2: for 2GR-FE

  2. A086154E10
    Using an oscilloscope, measure the waveform 1.
    CAN communication signal 
    Item
    Content
    Symbols (Terminal No.)
    CANH (E42-8) - GND (E42-24)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  3. A086155E11
    Using an oscilloscope, measure the waveform 2.
    CAN communication signal 
    Item
    Content
    Symbols (Terminal No.)
    CANL (E42-9) - GND (E42-24)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  4. E074977E11
    Using an oscilloscope, measure the waveform 3.
    Compressor and pulley operation signal 
    Item
    Content
    Symbols (Terminal No.)
    SOL+ (E42-13) - GND (E42-24)
    Tool Setting
    5 V/DIV., 500 μsec./DIV.
    Condition
    Engine idling, Blower switch LO, A/C switch ON

  5. E127551E01
    Using an oscilloscope, measure the waveform 4.
    Compressor lock sensor signal 
    Item
    Content
    Symbols (Terminal No.)
    LOCK (E42-3) - SG-2 (E42-10)
    Tool Setting
    500 mV/DIC., 20 msec./DIV.
    Condition
    Ignition switch on (IG), A/C switch ON, Magnetic clutch ON

← TERMINALS OF ECU (Nov 2005 – Jul 2007)DIAGNOSIS SYSTEM (from Nov 2005) →