Symbols (Terminal No.)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
S5-3 (E42-7) - GND (E42-24)
|
B - W-B
|
Power supply for pressure sensor
|
Ignition switch on (IG)
|
4.5 to 5.5 V
|
CANH (E42-8) - GND (E42-24)
|
V - W-B
|
Hi-level CAN bus line
|
Ignition switch on (IG)
|
Pulse generation (see waveform 1)
|
CANL (E42-9) - GND (E42-24)
|
W - W-B
|
Lo-level CAN bus line
|
Ignition switch on (IG)
|
Pulse generation (see waveform 2)
|
SG-3 (E42-23) - Body ground
|
B - Body ground
|
Ground for evaporator temperature sensor
|
Always
|
Below 1 Ω
|
PRE (E42-12) - SG-2 (E42-10)
|
L - G
|
Air conditioning pressure sensor signal
|
Refrigerant pressure: normal
|
0.76 to 4.74 V
|
PRE (E42-12) - SG-2 (E42-10)
|
L - G
|
Air conditioning pressure sensor signal
|
Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi]
|
Below 0.76 V
|
PRE (E42-12) - SG-2 (E42-10)
|
L - G
|
Air conditioning pressure sensor signal
|
Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi])
|
4.74 V or more
|
SG-2 (E42-10) - Body ground
|
G - Body ground
|
Ground for pressure sensor
|
Always
|
Below 1 Ω
|
SOL+ (E42-13) - GND (E42-24)
|
GR - W-B
|
A/C compressor operation signal
|
Engine idling
|
Pulse generation (see waveform 3)
|
Heater control (blower switch): 1
|
A/C switch ON
|
IG+ (E42-14) - GND (E42-24)
|
Y - W-B
|
Power source (IG)
|
Ignition switch on (IG)
|
10 to 14 V
|
SBLW (E42-21) - GND (E42-24)
|
GR - W-B
|
Blower motor ON signal
|
Ignition switch on (IG)
|
10 to 14 V → Below 1 V
|
Heater control (blower switch): 0 → 1
|
TE (E42-22) - SG-3 (E42-23)
|
W - B
|
Evaporator temperature sensor signal
|
Ignition switch on (IG)
|
1 to 1.3 V
|
Temperature near evaporator: 15°C (59°F)
|
GND (E42-24) - Body ground
|
W-B - Body ground
|
Ground for main power supply
|
Always
|
Below 1 Ω
|
A/C (E42-27) - GND (E42-24)
|
P - W-B
|
A/C switch signal
|
Ignition switch on (IG)
|
Below 1 V → 10 to 14 V
|
A/C switch OFF → ON
|
LED (E42-28) - Body ground
|
GR - Body ground
|
A/C switch indicator signal
|
Engine idling
|
10 to 14 V → Below 4 V
|
A/C switch ON
|
Heater control (blower switch): 0 → 1
|
PTC1 (E43-9)* - GND (E42-24)
|
W - W-B
|
PTC NO. 1 heater relay operation signal
|
Engine idling
|
Below 1 V → 10 to 14 V
|
Air mix control knob: Max hot
|
Engine coolant temperature: Below 65°C (149°F)
|
Ambient temperature: Below 10°C (50°F)
|
Heater control (blower switch): 0 → 1
|
Waiting time: 10 seconds
|
PTC2 (E43-10)* - GND (E42-24)
|
B - W-B
|
PTC NO. 2 heater relay operation signal
|
Engine idling
|
Below 1 V → 10 to 14 V
|
Air mix control knob: Max hot
|
Engine coolant temperature: Below 65°C (149°F)
|
Ambient temperature: Below 10°C (50°F)
|
Heater control (blower switch): 0 → 1
|
Waiting time: 20 seconds
|
HEAT (E43-14)* - Body ground
|
W - Body ground
|
MAX HOT switch detection signal
|
Ignition switch on (IG)
|
10 to 14 V
|
Air mix control knob: Max hot
|
Heater control (blower switch): 1
|
HLS (E43-23)* - Body ground
|
BR - Body ground
|
Headlight control signal
|
Engine idling
|
Below 1 V
|
Light control switch: head position
|
ALT (E43-24)* - GND (E42-24)
|
B - W-B
|
Alternator operation signal
|
Engine idling
|
Pulse generation
|