2005-2008 RAV4 · Service Manual HEATER & AIR CONDITIONING SYSTEM

Blower Motor Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

When the heater control (blower switch) is set to position 1 or higher, the contact of the HTR relay is closed, current flows to the blower motor, and the blower motor operates. The blower motor speed can be changed by exchanging the ground and the blower resistor circuit with the heater control (blower switch).

WIRING DIAGRAM

E125192E01

INSPECTION PROCEDURE


1. INSPECT FUSE (HTR)
  1. Remove the HTR fuse from the engine room No. 2 relay block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2. INSPECT HEATER RELAY (Marking: HTR)
B083458E01
  1. Remove the heater relay from the instrument panel junction block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 5
    10 kΩ or higher
    3 - 4
    10 kΩ or higher
    (when battery voltage is applied to terminals 1 and 2)
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE HEATER RELAY
OK


3. INSPECT BLOWER MOTOR
E120469E02
  1. Disconnect the E61 motor connector.

  1. Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the blower motor operates smoothly.

    OK:
    The blower motor operates smoothly.

  1. Measure the current.

    Standard current:
    Tester Connection
    Condition
    Specified Condition
    E61-1 - E61-2
    Blower motor operates
    1 to 3 A



NG
REPLACE BLOWER MOTOR
OK


4. CHECK WIRE HARNESS (HEATER CONTROL (BLOWER SWITCH) - BATTERY)
E120224E02
  1. Disconnect the E27 heater control connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E27-4 (LO) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. INSPECT HEATER CONTROL (BLOWER SWITCH)
E117010E06
  1. Remove the heater control.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    ALL - 5 (E)
    0
    10 kΩ or higher
    4 (LO) - 5 (E)
    1
    Below 1 Ω
    4 (LO) - 5 (E) - 9 (M1)
    1 to 2
    Below 1 Ω
    4 (LO) - 5 (E) - 9 (M1)
    2
    Below 1 Ω
    4 (LO) - 5 (E) - 9 (M1) - 10 (M2)
    2 to 3
    Below 1 Ω
    4 (LO) - 5 (E) - 10 (M2)
    3
    Below 1 Ω
    4 (LO) - 5 (E) - 10 (M2) - 6(HI)
    3 to 4
    Below 1 Ω
    4 (LO) - 5 (E) - 6 (HI)
    4
    Below 1 Ω



NG
REPLACE HEATER CONTROL
OK


6. INSPECT BLOWER RESISTOR
E120977E02
  1. Remove the blower resistor.

  1. Measure the resistance of the resistor.

    Standard resistance:
    for LHD
    Tester Connection
    Specified Condition
    E62-4 (E) - E62-1 (HI)
    3.12 to 3.60 Ω
    E62-4 (E) - E62-3 (M2)
    1.45 to 1.67 Ω
    E62-4 (E) - E62-2 (M1)
    0.52 to 0.60 Ω
    for RHD
    Tester Connection
    Specified Condition
    E62-1 (E) - E62-4 (HI)
    3.12 to 3.60 Ω
    E62-1 (E) - E62-2 (M2)
    1.45 to 1.67 Ω
    E62-1 (E) - E62-3 (M1)
    0.52 to 0.60 Ω



NG
REPLACE BLOWER RESISTOR
OK


7. CHECK WIRE HARNESS (HEATER CONTROL (BLOWER SWITCH) - BLOWER RESISTOR)

  1. E120283E04
    Disconnect the E27 heater control connector.

  1. Disconnect the E62 blower resistor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LHD
    Tester Connection
    Specified Condition
    E27-6 (HI) - E62-1 (HI)
    Below 1 Ω
    E27-9 (M1) - E62-2 (M1)
    Below 1 Ω
    E27-10 (M2) - E62-3 (M2)
    Below 1 Ω
    E27-5 (E) - Body ground
    Below 1 Ω
    E62-4 (E) - Body ground
    Below 1 Ω
    for RHD
    Tester Connection
    Specified Condition
    E27-6 (HI) - E62-4 (HI)
    Below 1 Ω
    E27-9 (M1) - E62-3 (M1)
    Below 1 Ω
    E27-10 (M2) - E62-2 (M2)
    Below 1 Ω
    E27-5 (E) - Body ground
    Below 1 Ω
    E62-1 (E) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. CHECK WIRE HARNESS (BLOWER RESISTOR - BLOWER MOTOR)
E120282E02
  1. Disconnect the E62 blower resistor connector.

  1. Disconnect the E61 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LHD
    Tester Connection
    Specified Condition
    E62-4 (E) - E61-1
    Below 1 Ω
    for RHD
    Tester Connection
    Specified Condition
    E62-1 (E) - E61-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


9. CHECK WIRE HARNESS (BLOWER MOTOR - BODY GROUND)
E119793E02
  1. Disconnect the E61 motor connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E61-2 - Body ground
    Below 1 Ω

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E61-2 - Body ground
    Ignition switch on (IG)
    Heater control (blower switch) 1
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


10. CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BATTERY)
E123550E05
  1. Disconnect the E42 amplifier connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E42-21 (SBLW) - Body ground
    Ignition switch on (IG)
    Heater control (blower switch): 0
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


11. CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BODY GROUND)
E123550E04
  1. Disconnect the E42 amplifier connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E42-24 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← B1499/99 Multiplex Communication Circuit (from Jan 2007)Compressor Circuit (from Aug 2007) →