2005-2008 RAV4 · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Nov 2005

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. When removing the moulding, heat the vehicle body and moulding using a heat light.

    Standard heating temperature:
    Item
    Specified Condition
    Vehicle body
    40 to 60°C (104 to 140°F)
    Clip
    20 to 30°C (68 to 86°F)

    NOTICE:
    Do not heat the vehicle body and moulding excessively.


1. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH

  1. B127958
    Put protective tape around the moulding.

  1. Remove the 4 screws and detach the 2clips..

  1. Using a moulding remover, detach the 9 clips and remove the moulding.

    NOTICE:
    1. If reusing the moulding, take care not to damage the moulding.
    2. Be careful not to damage the vehicle body.


2. REMOVE NO. 2 REAR WHEEL OPENING EXTENSION LH
  1. Put protective tape around the moulding.

  1. B130248
    Remove the screw.

  1. Using a moulding remover, detach the 2 clips and remove the extension.

    NOTICE:
    1. If reusing the extension, take care not to damage the extension.
    2. Be careful not to damage the vehicle body.


3. REMOVE NO. 1 REAR WHEEL OPENING EXTENSION LH
  1. Put protective tape around the moulding.

  1. B133203E01
    Using a drill bit of less than φ 4 mm (0.16 in.), drill out the 3 rivet flanges.

    HINT:
    Wind tape around the drill bit approximately 5 mm (0.20 in.) from the tip of the drill.

    NOTICE:
    1. Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.
    2. Be careful as the cut rivet will be very hot.

  1. Continue drilling and push out the remaining rivet fragments using the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Using a heat light, heat the extension and vehicle body.

  1. Cut the double-sided tape that holds the moulding to the vehicle body with a knife.

    NOTICE:
    1. If reusing the extension, take care not to damage the extension.
    2. Be careful not to damage the vehicle body.

  1. B127959
    Using a moulding remover, detach the 5 clips and remove the extension.


4. REMOVE REAR QUARTER OUTSIDE MOULDING LH
  1. Put protective tape around the moulding.

  1. B133204
    Using a drill bit of less than φ 4 mm (0.16 in.), drill out the 3 rivet flanges.

    HINT:
    Wind tape around the drill bit approximately 5 mm (0.20 in.) from the tip of the drill.

    NOTICE:
    1. Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.
    2. Be careful as the cut rivet will be very hot.

  1. Continue drilling and push out the remaining rivet fragments using the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Using a heat light, heat the moulding and vehicle body.

  1. B127960
    Using a moulding remover, detach the 5 clips and remove the moulding.

    NOTICE:
    1. If reusing the moulding, take care not to damage the moulding.
    2. Be careful not to damage the vehicle body.


5. REMOVE NO. 2 ROCKER PANEL MOULDING PROTECTOR LH

  1. B133713
    Remove the 2 screws and retainer.


6. REMOVE QUARTER OPENING RETAINER LH

  1. B133714
    Remove the 4 screws and retainer.


7. REMOVE NO. 1 ROCKER PANEL MOULDING RETAINER

  1. B133715
    Remove the 4 screws and 2 retainers.

← COMPONENTS (from Nov 2005)INSTALLATION (from Nov 2005) →