2005-2008 RAV4 · Service Manual HEATER & AIR CONDITIONING SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Jul 2007 from Aug 2007


CHECK AIR CONDITIONING AMPLIFIER
E115964E04
  1. Measure the voltage and resistance of the connectors.

    HINT:
    Check from the rear of the connector while it is connected to the air conditioning amplifier.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    SOL+ (E41-2) - GND (E41-14)
    GR - W-B
    A/C compressor operation signal
    Engine idling
    Pulse generation
    (see waveform 1)
    Refrigerant pressure: normal
    Always
    Blower switch LO
    A/C switch ON
    PRE (E41-9) - SG-2 (E41-13)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi])
    Below 0.76 V
    PRE (E41-9) - SG-2 (E41-13)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi])
    4.74 V or higher
    BLW (E41-23) - GND (E41-14)
    R - W-B
    Blower motor control signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    Blower switch LO
    TSD (E41-33) - S5-4 (E41-31)
    L - LG
    Driver side solar sensor signal
    Ignition switch on (IG)
    0.8 to 4.3 V
    Solar sensor subject to electric light
    TSP (E41-32) - S5-4 (E41-31)
    P - LG
    Passenger side solar sensor signal
    Ignition switch on (IG)
    0.8 to 4.3 V
    Solar sensor subject to electric light
    TR (E41-29) - SG-1 (E41-34)
    GR- V
    Room temperature sensor signal
    Ignition switch on (IG)
    1.8 to 2.2 V
    Vehicle interior temperature: 25°C (77°F)
    SG-1 (E41-34) - Body ground
    V - Body ground
    Ground for room temperature sensor
    Always
    Below 1 V
    GND (E41-14) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 V
    IG+ (E41-1) - GND (E41-14)
    Y - W-B
    Power source (IG)
    Ignition switch on (IG)
    10 to 14 V
    S5-3 (E41-10) - GND (E41-14)
    B - W-B
    Power supply for pressure sensor
    Ignition switch on (IG)
    4.5 to 5.5 V
    CANH (E41-11) - GND (E41-14)
    V - W-B
    Hi-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 3)
    CANL (E41-12) - GND (E41-14)
    W - W-B
    Lo-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 4)
    RDEF (E41-38) - GND (E41-14)
    B - W-B
    Rear defogger switch signal
    Ignition switch on (IG)
    Rear defogger switch OFF
    10 to 14 V
    RDEF (E41-38) - GND (E41-14)
    B - W-B
    Rear defogger switch signal
    Ignition switch on (IG)
    Rear defogger switch ON
    Below 1 V
    SG-2 (E41-13) - Body ground
    G - Body ground
    Ground for pressure sensor
    Always
    Below 1 V
    PTC1 (E41-3) - Body ground(*1)
    W - Body ground
    PTC NO. 1 heater relay operation signal
    Engine idling
    Below 1 V → 10 to 14 V
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Light control switch: OFF
    Blower switch OFF → LO
    PTC2 (E41-22) - Body ground(*1)
    B - Body ground
    PTC NO. 2 heater relay operation signal
    Engine idling
    Below 1 V → 10 to 14 V
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Light control switch: OFF
    Blower switch OFF → LO
    ALT (E41-25) - Body ground(*1)
    B - Body ground
    Generator signal
    Engine idling
    Pulse generation
    HLS (E41-27) - Body ground(*1)
    BR - Body ground
    Headlight signal
    Engine idling
    Below 1 V
    Light control switch: ON
    LIN1 (E41-37) - GND (E41-14)
    B - W-B
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    LOCK (E41-8) - SG-2 (E41-13)(*2)
    W - G
    Compressor lock sensor signal
    Ignition switch on (IG)
    AUTO switch ON
    A/C switch ON
    Magnetic clutch ON
    Pulse generation
    (see waveform 5)
    MGC (E41-20) - GND (E41-14)(*2)
    V - W-B
    Magnetic clutch relay signal
    Ignition switch on (IG)
    Magnetic clutch OFF
    10 to 14 V
    MGC (E41-20) - GND (E41-14)(*2)
    V - W-B
    Magnetic clutch relay signal
    Ignition switch on (IG)
    Magnetic clutch ON
    Below 1.5 V
    BUB G (c1-2) - Body ground
    -
    Ground for BUS IC
    Always
    Below 1 V
    BUS (c1-3) - BUB G (c1-2)
    -
    BUS IC control signal
    Ignition switch on (IG)
    Pulse generation
    B BUS (c1-4) - BUB G (c1-2)
    -
    Power supply for BUS IC
    Ignition switch on (IG)
    11 to 13 V
    SGA (c1-5) - Body ground
    -
    Ground for evaporator temperature sensor
    Always
    Below 1 V
    TEA (c1-6) - SGA (c1-5)
    -
    Evaporator temperature sensor signal
    Ignition switch on (IG)
    1.4 to 1.8 V
    Evaporator temperature: 15°C (59°F)

    HINT:
    *1: w/ PTC heater
    *2: for 2GR-FE

  2. E074977E11
    Using an oscilloscope, measure the waveform 1.
    Compressor and pulley operation signal 
    Item
    Content
    Symbols (Terminal No.)
    SOL+ (E41-2) - GND (E41-14)
    Tool Setting
    5 V/DIV., 500 μsec./DIV.
    Condition
    Engine idling, Blower switch LO, A/C switch ON

  3. E103396E05
    Using an oscilloscope, measure the waveform 2.
    Blower motor control signal 
    Item
    Content
    Symbols (Terminal No.)
    BLW (E41-23) - GND (E41-14)
    Tool Setting
    1 V/DIV., 500 μsec./DIV.
    Condition
    Ignition switch on (IG), Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.

  4. A086154E10
    Using an oscilloscope, measure the waveform 3.
    CAN communication signal 
    Item
    Content
    Symbols (Terminal No.)
    CANH (E41-11) - GND (E41-14)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  5. A086155E11
    Using an oscilloscope, measure the waveform 4.
    CAN communication signal 
    Item
    Content
    Symbols (Terminal No.)
    CANL (E41-12) - GND (E41-14)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  6. E127551E01
    Using an oscilloscope, measure the waveform 5.
    Compressor lock sensor signal 
    Item
    Content
    Symbols (Terminal No.)
    LOCK (E41-8) - SG-2 (E41-13)
    Tool Setting
    500 mV/DIV., 20 msec./DIV.
    Condition
    Ignition switch on (IG), AUTO switch ON, A/C switch ON, Magnetic clutch ON


CHECK AIR CONDITIONING CONTROL
E123518E02
  1. Measure the voltage and resistance of the connectors.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IG+ (E26-2) - GND (E26-7)
    L - W-B
    Power source (IG)
    Ignition switch on (IG)
    10 to 14 V
    GND (E26-7) - Body ground
    W-B - Body Ground
    Ground for air conditioning control assembly
    Always
    Below 1 V
    LIN1 (E26-11) - GND (E26-7)
    B - W-B
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    +B (E26-1) - GND (E26-7)
    R - W-B
    Power source (Back-up)
    Always
    10 to 14 V
    ACC (E26-8) - GND (E26-7)
    GR - W-B
    ACC power supply
    Ignition switch on (ACC)
    10 to 14 V

← TERMINALS OF ECU (Nov 2005 – Jul 2007)DIAGNOSIS SYSTEM (from Nov 2005) →