2005-2008 RAV4 · Service Manual HEATER & AIR CONDITIONING SYSTEM

PTC Heater Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

PTC heater relays are closed in accordance with signals from the air conditioning amplifier and power is supplied to the PTC heater installed on the radiator heater unit.

WIRING DIAGRAM

E123536E01

INSPECTION PROCEDURE


1. INSPECT FUSE (PTC1, PTC2)
  1. Remove the PTC1 and PTC2 H-fuses from the engine room No. 2 relay block.

  1. Measure the resistance of the H-fuses.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2. INSPECT PTC HEATER RELAY (Marking: PTC NO. 1, PTC NO. 2)
A092673E24
  1. Remove the No. 1 and No. 2 PTC heater relays from the engine room No. 2 relay block.

  1. Measure the resistance of the relays.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE PTC HEATER ASSEMBLY
OK


3. CHECK AIR CONDITIONING AMPLIFIER
E115805E06
  1. Remove the air conditioning amplifier with its connectors still connected.

  1. Turn the ignition switch on (IG).

  1. When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.

  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    E41-3 (PTC1) - Body ground
    10 to 14 V
    E41-22 (PTC2) - Body ground
    10 to 14 V



NG
Go to step 6
OK


4. CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - PTC HEATER RELAY)
E123537E01
  1. Remove the No. 1 and No. 2 PTC heater relays from the engine room No. 2 relay block.

  1. Turn the ignition switch on (IG).

  1. When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.

  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    No. 1 PTC heater relay terminal 2 - Body ground
    10 to 14 V
    No. 2 PTC heater relay terminal 1 - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. CHECK WIRE HARNESS (PTC HEATER RELAY - BODY GROUND)
E123537E01
  1. Remove the No. 1 and No. 2 PTC heater relays from the engine room No. 2 relay block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    No. 1 PTC heater relay terminal 1 - Body ground
    Below 1 Ω
    No. 2 PTC heater relay terminal 2 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6. CHECK WIRE HARNESS (PTC HEATER RELAY - PTC HEATER ASSEMBLY)
E123538E01
  1. Remove the No. 1 and No. 2 PTC heater relays from the engine room No. 2 relay block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    No. 1 PTC heater relay terminal 3 - A29-3 (B)
    Below 1 Ω
    No. 2 PTC heater relay terminal 3 - A29-2 (B)
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7. CHECK WIRE HARNESS (BATTERY - PTC HEATER RELAY)
E123537E01
  1. Remove the No. 1 and No. 2 PTC heater relays from the engine room No. 2 relay block.

  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Specified Condition
    No. 1 PTC heater relay terminal 5 - Body ground
    10 to 14 V
    No. 2 PTC heater relay terminal 5 - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. CHECK PTC HEATER
  1. After replacing the PTC heater with a normal one, check that the PTC heater function operates normally.

    OK:
    PTC heater function operates normally.



OK
REPLACE PTC HEATER
NG

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Compressor Circuit (from Aug 2007)IG Power Source Circuit (from Nov 2005) →