2005-2008 RAV4 · Service Manual BRAKE

C1249/49 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built Aug 2007 – Jul 2008

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008

DESCRIPTION

The skid control ECU detects the brake operating conditions through a signal transmitted by the stop light switch. The skid control ECU incorporates an open circuit detection circuit. This DTC is set under either of the following conditions:
  1. An open is detected in the stop light signal input line when the stop light switch is off.
  2. An open is detected in the stop light circuit lead to the ground when the stop light switch is off.
DTC No.
DTC Detection Condition
Trouble Area
C1249/49
When IG1 terminal voltage is 9.5 to 18.5 V, open circuit of stop light switch continues for 3 seconds or more.
  1. STOP fuse
  2. Stop light switch
  3. Stop light switch circuit
  4. Brake actuator (Skid control ECU)

WIRING DIAGRAM

C133588E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Check the Data List for proper functioning of the stop light switch.

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Conditions
    Stop Lamp SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released

    OK:
    ON (brake pedal is depressed) appears on the screen.



NG
Go to step 3
OK


2. CHECK WIRE HARNESS (STP VOLTAGE)

  1. C117862E10
    Disconnect the A27 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A27-10 (STP) - Body ground
    Brake pedal depressed
    8 to 14 V
    A27-10 (STP) - Body ground
    Brake pedal released
    Below 4.0 V



NG
Go to step 5
OK

REPLACE BRAKE ACTUATOR ASSEMBLY

3. INSPECT FUSE (STOP)
  1. Remove the STOP fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


4. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. C108891E01
    Disconnect the stop light switch connector.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    1 - 2
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin not pushed
    10 kΩ or higher
    3 - 4
    Pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


5. CHECK WIRE HARNESS (SKID CONTROL ECU - STOP LIGHT SWITCH)

  1. C118696E02
    Disconnect the A27 ECU connector.

  1. Disconnect the A5 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A27-10 (STP) - A5-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← C1249/49 Open in Stop Light Switch Circuit (Jan 2007 – Jul 2007)C1249/49 Open in Stop Light Switch Circuit (from Aug 2008) →