2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2007


1. INSTALL FUEL INJECTOR ASSEMBLY

  1. A129475E01
    Apply a light coat of spindle oil or gasoline to 6 new O-rings, and install one to each injector.

  1. A129476E01
    Apply a light coat of spindle oil or gasoline where the fuel delivery pipe contacts the O-ring.

  1. Push the fuel injector while twisting it back and forth to install it in the fuel delivery pipe.

  1. Position the fuel injector connector outward.

    NOTICE:
    1. Be careful not to twist the O-ring.
    2. After installing the fuel injector, check that it turns smoothly. If it does not, reinstall it with a new O-ring.

  1. A129472
    Install 6 new insulators to the intake manifold.

  1. A129471
    Place the fuel delivery pipe together with the 6 fuel injectors into the intake manifold.

    NOTICE:
    Be careful not to drop the fuel injectors when installing the fuel delivery pipe.

  1. A129458E02
    Temporarily install the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.

    NOTICE:
    After installing the fuel injector, check that it turns smoothly. If it does not, reinstall it with a new O-ring.

  1. Tighten the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A129470
    Connect the 6 fuel injector connectors.


2. CONNECT FUEL MAIN TUBE

  1. A129477E01
    Push in the tube connector to the pipe until the tube connector makes a "click" sound.

    NOTICE:
    1. Check that there is no damage or foreign objects on the connected part of the fuel pipe.
    2. After connecting, check if the fuel tube connector and the pipe are securely connected by pulling on them.

  1. Install the No. 2 fuel pipe clamp.


3. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

NOTICE:
DO NOT apply oil to the bolts listed below: :
Tightening Parts
Surge Tank and Intake Manifold
No. 1 Surge Tank Stay and Cylinder Head Cover
No. 1 Surge Tank Stay and Surge Tank
Throttle Body Bracket and Cylinder Head Cover
Throttle Body Bracket and Surge Tank

  1. Install a new gasket to the surge tank.

  1. A139209
    Using a 5 mm hexagon socket wrench, install the 4 bolts and 2 nuts.

    Torque:
    Bolt:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }
    Nut:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. Install the throttle body bracket and No. 1 surge tank stay with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A129467
    Connect the connector.

  1. Connect the No. 1 ventilation hose and vacuum hose.

  1. A129464
    Install the clamp and connect the throttle body connector.

  1. Connect the vapor feed hose.

  1. Connect the 2 water by-pass hoses to the throttle body.


4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner filter element onto the air cleaner case.

  1. A137901E01
    Insert the hinge part of the air cleaner cap into the air cleaner case, then hang the 2 hook clamps.

  1. A173728
    Tighten the No. 1 air cleaner hose clamp.

  1. Connect the No. 2 ventilation hose to the air cleaner hose.

  1. Connect the 2 wire harness clamps and 2 vacuum hoses.

  1. Connect the VSV (intake air control) connector.

  1. Connect the mass air flow meter connector.


5. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.

  1. A112307E01
    Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir's filler neck.

    Standard capacity:
    9.3 liters (9.8 US qts, 8.2 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. Start the engine and warm it up until the cooling fan operates. While the cooling fan operates, circulate the coolant for several minutes.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Specified Condition
      Manual Air Conditioning System
      Fan speed: Any setting except OFF
      Temperature: Toward WARM
      Air conditioning switch: OFF
      Automatic Air Conditioning System
      Temperature: Toward MAX
      Air conditioning switch: OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that some coolant remains in the radiator reservoir.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.
      4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
      5. Run the engine at 2,000 rpm until the coolant level has stabilized.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times to bleed air.

    CAUTION:
    When squeezing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.

  1. A112306
    Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

7. INSPECT FOR COOLANT LEAK
  1. Remove the radiator reservoir cap.

    CAUTION:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A126962E01
    Fill the radiator with coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage.
    If there are no signs of external coolant leaks, check the heater core, cylinder block and head.

  1. Reinstall the radiator cap.


8. INSPECT FOR FUEL LEAK

HINT:
(Click here).


9. INSPECT V-BANK COVER SUB-ASSEMBLY

  1. A137900
    Attach the 3 clips to install the engine cover.

← INSPECTION (from Aug 2007)COMPONENTS (Aug 2007 – Jul 2008) →