2005-2008 RAV4 · Service Manual RESTRAINTS

B1651/33 Manual Cut off Switch Trouble

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

The passenger airbag manual cut-off switch circuit consists of parts including the center airbag sensor and the airbag cut-off switch.
DTC B1651/33 is set when a malfunction is detected in the airbag cut-off switch circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1651/33
When one of following conditions is met:
  1. Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in airbag cut-off switch circuit for 2 seconds
  2. Airbag cut-off switch malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Passenger airbag manual cut-off switch
  3. Center airbag sensor

WIRING DIAGRAM

C128680E02

INSPECTION PROCEDURE


1. CHECK FOR DTC
H101852E03
  1. Turn the ignition switch on (IG).

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1651/33 is not output.

    HINT:
    DTCs other than DTC B1651/33 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2. CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the airbag cut-off switch.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTOR
OK


3. INSPECT AIRBAG CUT-OFF SWITCH
C128731E01
  1. Disconnect the E68 passenger airbag manual cut-off switch connector.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (PMC-) - 2 (PMC+)
    OFF
    80 to 120 Ω
    1 (PMC-) - 2 (PMC+)
    ON
    320 to 480 Ω



NG
REPLACE AIRBAG CUT-OFF SWITCH
OK


4. CHECK INSTRUMENT PANEL WIRE (FOR OPEN)
H100193E04
  1. Disconnect the instrument panel wire connector from the airbag cut-off switch.

  1. Using a service wire, connect E68-1 (PMC-) and E68-2 (PMC+) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E49-11 (MSW+) - E49-12 (MSW-)
    Below 1 Ω



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


5. CHECK INSTRUMENT PANEL WIRE (FOR SHORT)
H100192E03
  1. Disconnect the service wire from connector C.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E49-11 (MSW+) - E49-12 (MSW-)
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


6. CHECK INSTRUMENT PANEL WIRE (TO B+)
H100192E03
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E49-11 (MSW+)- Body ground
    Below 1 V
    E49-12 (MSW-) - Body ground
    Below 1 V



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


7. CHECK INSTRUMENT PANEL WIRE (TO GROUND)
H100192E03
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E49-11 (MSW+) - Body ground
    1 MΩ or higher
    E49-12 (MSW-) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE INSTRUMENT PANEL WIRE
OK


8. CHECK CENTER AIRBAG SENSOR ASSEMBLY
H101852E03
  1. Connect the connectors to the center airbag sensor and airbag cut-off switch.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1651/33 is not output.

    HINT:
    DTCs other than DTC B1651/33 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK


← B1648/82 Front Passenger Side Satellite Sensor Bus Initialization Incomplete (from Aug 2008)B1651/33 Manual Cut off Switch Trouble (from Jan 2007) →