B1648/82 Front Passenger Side Satellite Sensor Bus Initialization Incomplete
Diagnostic trouble codes · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008
DESCRIPTION
The front passenger side - side airbag sensor consists of parts including the diagnostic circuit and the lateral deceleration sensor.When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1648/82 is set when a malfunction is detected in the front passenger side - side airbag sensor circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1648/82 |
When one of following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
![]() ![]() |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1627/82 is not output.
DTC B1637/82 is not output.
- HINT:
- DTCs other than DTC B1627/82 and B1637/82 may be output at this time, but they are not related to this check.
|
|
||||
| OK | |
| 2. CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, front passenger side rear airbag sensor and the front passenger side - side airbag sensor.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 3. CHECK FLOOR WIRE (OPEN) |
![]() ![]() |
Disconnect the connectors from the center airbag sensor and the front passenger side - side airbag sensor.
for LHD:Using a service wire, connect L6-4 (BBR+) and L6-3 (BBR-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
for RHD:Using a service wire, connect K10-4 (BBL+) and K10-3 (BBL-) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
L3-8 (BBP+) - L3-11 (BBP-)
Below 1 Ω
- for RHD:
Tester Connection
Specified Condition
K2-8 (BBP+) - K2-11 (BBP-)
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK FLOOR WIRE (SHORT) |
![]() ![]() |
Disconnect the service wire from connector C.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
L3-8 (BBP+) - L3-11 (BBP-)
1 MΩ or higher
- for RHD:
Tester Connection
Specified Condition
K2-8 (BBP+) - K2-11 (BBP-)
1 MΩ or higher
|
|
||||
| OK | |
| 5. CHECK FLOOR WIRE (TO B+) |
![]() ![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
- for LHD:
Tester Connection
Specified Condition
L3-8 (BBP+) - Body ground
Below 1 V
L3-11 (BBP-) - Body ground
Below 1 V
- for RHD:
Tester Connection
Specified Condition
K2-8 (BBP+) - Body ground
Below 1 V
K2-11 (BBP-) - Body ground
Below 1 V
|
|
||||
| OK | |
| 6. CHECK FLOOR WIRE (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
L3-8 (BBP+) - Body ground
1 MΩ or higher
L3-11 (BBP-) - Body ground
1 MΩ or higher
- for RHD:
Tester Connection
Specified Condition
K2-8 (BBP+) - Body ground
1 MΩ or higher
K2-11 (BBP-) - Body ground
1 MΩ or higher
|
|
||||
| OK | |
| 7. CHECK FLOOR WIRE (OPEN) |


Disconnect the connectors from the front passenger side - side airbag sensor and the front passenger side rear airbag sensor.
for LHD:Using a service wire, connect L20-1 (BCR-) and L20-2 (BCR+) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
for RHD:Using a service wire, connect K26-1 (BCL-) and K26-2 (BCL+) of connector C.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
L6-1 (BCR+) - L6-2 (BCR-)
Below 1 Ω
- for RHD:
Tester Connection
Specified Condition
K10-1 (BCL+) - K10-2 (BCL-)
Below 1 Ω
|
|
||||
| OK | |
| 8. CHECK FLOOR WIRE (SHORT) |
![]() ![]() |
Disconnect the service wire from connector C.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
L6-1 (BCR+) - L6-2 (BCR-)
1 MΩ or higher
- for RHD:
Tester Connection
Specified Condition
K10-1 (BCL+) - K10-2 (BCL-)
1 MΩ or higher
|
|
||||
| OK | |
| 9. CHECK FLOOR WIRE (TO B+) |
![]() ![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
- for LHD:
Tester Connection
Specified Condition
L6-1 (BCR+) - Body ground
Below 1 V
L6-2 (BCR-) - Body ground
Below 1 V
- for RHD:
Tester Connection
Specified Condition
K10-1 (BCL+) - Body ground
Below 1 V
K10-2 (BCL-) - Body ground
Below 1 V
|
|
||||
| OK | |
| 10. CHECK FLOOR WIRE (TO GROUND) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
L6-1 (BCR+) - Body ground
1 MΩ or higher
L6-2 (BCR-) - Body ground
1 MΩ or higher
- for RHD:
Tester Connection
Specified Condition
K10-1 (BCL+) - Body ground
1 MΩ or higher
K10-2 (BCL-) - Body ground
1 MΩ or higher
|
|
||||
| OK | |
| 11. CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR |
![]() ![]() |
Connect the connectors to the center airbag sensor.
Interchange the front passenger side - side airbag sensor with the driver side - side airbag sensor and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
Result Result
Proceed to
DTC B1643/81 and B1648/82 are not output
A
DTC B1648/82 is output
B
DTC B1643/81 is output
C
- HINT:
- DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
| 12. CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the front passenger side rear airbag sensor with the driver side rear airbag sensor and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
Result Result
Proceed to
DTC B1643/81 and B1648/82 are not output
A
DTC B1648/82 is output
B
DTC B1643/81 is output
C
- HINT:
- DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||






