C1231/31 Steering Angle Sensor Circuit Malfunction
Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008
DESCRIPTION
The steering sensor signal is sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering sensor zero point malfunction diagnostic function.| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1231/31 |
When IG1 terminal voltage 9.5 V or more, steering angle sensor malfunction signal received. |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- When U0073/94, U0123/62, U0124/95 or U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62, U0124/95 or U0126/63 first.
- When there are problems with the speed sensor or the yaw rate sensor, DTCs for the steering sensor may be output even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor are output together with other DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor first, and then inspect and repair the steering sensor.
- When U0073/94, U0123/62, U0124/95 or U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62, U0124/95 or U0126/63 first.
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the Data List of the intelligent tester, check for any momentary interruptions in the wire harness and connectors between the skid control ECU and the steering sensor (Click here).
Skid control ECU Item (Display)
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
Steering Open
Steering angle sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
- OK:
- There are no momentary interruptions.
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. CHECK DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG) again and check that no CAN communication system DTC is output.
Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (24 mph) and check that no speed and yaw rate sensor DTCs are output.
Result Result
Proceed to
DTC is not output
A
CAN communication system DTC is output
B
Speed sensor or yaw rate sensor DTC is output
C
|
|
||||
|
|
||||
| A | |
| 3. CHECK WIRE HARNESS (STEERING SENSOR - BATTERY AND BODY GROUND) |
![]() ![]() |
Remove the steering wheel assembly and the column cover.
Disconnect the E14 sensor connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E14-1 (IG) - Body ground
Ignition switch on (IG)
10 to 14 V
E14-3 (BAT) - Body ground
Always
10 to 14 V
Measure the resistance of the wire harness side connector.
- Standard resistance:
Tester Connection
Specified Condition
E14-2 (ESS) - Body ground
Below 1Ω
|
|
||||
| OK | ||
| ||
| 4. REPAIR OR REPLACE HARNESS AND CONNECTOR (STEERING SENSOR TO SKID CONTROL ECU) |
| NEXT | |
| 5. RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle and turn the steering wheel to the right and left at a speed of 45 km/h (28 mph) or more for several seconds.
Check if the same DTC is recorded (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||

