2005-2008 RAV4 · Service Manual BRAKE

C1231/31 Steering Angle Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008

DESCRIPTION

The steering sensor signal is sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering sensor zero point malfunction diagnostic function.
DTC No.
DTC Detection Condition
Trouble Area
C1231/31
When IG1 terminal voltage 9.5 V or more, steering angle sensor malfunction signal received.
  1. Steering sensor
  2. Steering sensor circuit
  3. Steering sensor power supply
  4. CAN communication system

WIRING DIAGRAM

C126310E01
C126311E01

INSPECTION PROCEDURE

HINT:
  1. When U0073/94, U0123/62, U0124/95 or U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62, U0124/95 or U0126/63 first.
  2. When there are problems with the speed sensor or the yaw rate sensor, DTCs for the steering sensor may be output even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor are output together with other DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor first, and then inspect and repair the steering sensor.


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Data List of the intelligent tester, check for any momentary interruptions in the wire harness and connectors between the skid control ECU and the steering sensor (Click here).

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Steering Open
    Steering angle sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
Go to step 4
OK


2. CHECK DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG) again and check that no CAN communication system DTC is output.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (24 mph) and check that no speed and yaw rate sensor DTCs are output.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    CAN communication system DTC is output
    B
    Speed sensor or yaw rate sensor DTC is output
    C



B
CHECK AND REPLACE CAN COMMUNICATION SYSTEM

C
REPAIR CIRCUIT INDICATED BY OUTPUT DTC
A


3. CHECK WIRE HARNESS (STEERING SENSOR - BATTERY AND BODY GROUND)
C130038E01
  1. Remove the steering wheel assembly and the column cover.

  1. Disconnect the E14 sensor connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E14-1 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    E14-3 (BAT) - Body ground
    Always
    10 to 14 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E14-2 (ESS) - Body ground
    Below 1Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE STEERING SENSOR

4. REPAIR OR REPLACE HARNESS AND CONNECTOR (STEERING SENSOR TO SKID CONTROL ECU)

NEXT


5. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 45 km/h (28 mph) or more for several seconds.

  1. Check if the same DTC is recorded (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 2
A

END


← C1223/43 ABS Control System Malfunction (Aug 2007 – Jul 2008)C1231/31 Steering Angle Sensor Circuit Malfunction (Jan 2007 – Jul 2007) →