B1820/55 Short in Front Driver Side - Side Squib Circuit
Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006
Also covers:
- B1821/55 Open in Front Driver Side - Side Squib Circuit
- B1822/55 Short to GND in Front Driver Side - Side Squib Circuit
- B1823/55 Short to B+ in Front Driver Side - Side Squib Circuit
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
The driver side - side squib circuit consists of the center airbag sensor and the front seat side airbag LH.This circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side - side squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1820/55 |
Center airbag sensor receives a line short signal 5 times in the driver side - side squib circuit during primary check. |
|
| B1821/55 |
Center airbag sensor receives an open signal in the driver side - side squib circuit for 2 seconds. |
|
| B1822/55 |
Center airbag sensor receives a short to ground signal in the driver side - side squib circuit for 0.5 seconds. |
|
| B1823/55 |
Center airbag sensor receives a short to B+ signal in the driver side - side squib circuit for 0.5 seconds. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
- After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
| 1. CHECK DRIVER SIDE FRONT SEAT SIDE AIRBAG ASSEMBLY (DRIVER SIDE - SIDE SQUIB) |
![]() ![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the driver side front seat side airbag.
Connect the black wire side of SST to connector E.
- CAUTION:
- Never connect a tester to the driver side - side airbag (driver side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting.
- SST
- 09843-18060
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (Click here).
- OK:
- DTC B1820, B1821, B1822, B1823 or 55 is not output.
- HINT:
- DTCs other than DTC B1820, B1821, B1822, B1823 or 55 may be output at this time, but they are not related to this check.
|
|
||||
| NG | |
| 2. CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from the No. 1 seat airbag wire.
Check that the floor wire connectors (on the driver side - side squib) are not damaged.
- OK:
- Lock button is not disengaged, and claw of lock is not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK FLOOR WIRE (DRIVER SIDE - SIDE SQUIB CIRCUIT) |
![]() ![]() |
Disconnect the connector from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
- for LHD:
Tester Connection
Specified Condition
e1-1 (SFD+) - Body ground
Below 1 V
e1-2 (SFD-) - Body ground
Below 1 V
- for RHD:
Tester Connection
Specified Condition
f1-1 (SFD+) - Body ground
Below 1 V
f1-2 (SFD-) - Body ground
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
e1-1 (SFD+) - e1-2 (SFD-)
Below 1 Ω
e1-1 (SFD+) - Body ground
1 MΩ or higher
e1-2 (SFD-) - Body ground
1 MΩ or higher
- for RHD:
Tester Connection
Specified Condition
f1-1 (SFD+) - f1-2 (SFD-)
Below 1 Ω
f1-1 (SFD+) - Body ground
1 MΩ or higher
f1-2 (SFD-) - Body ground
1 MΩ or higher
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
e1-1 (SFD+) - e1-2 (SFD-)
1 MΩ or higher
- for RHD:
Tester Connection
Specified Condition
f1-1 (SFD+) - f1-2 (SFD-)
1 MΩ or higher
|
|
||||
| NG | |
| 4. CHECK NO. 1 SEAT AIRBAG WIRE |
Disconnect the No. 1 seat airbag wire connector from the floor wire.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
- Standard voltage:
- for LHD:
Tester Connection
Specified Condition
e1-1 (SFD+) - Body ground
Below 1 V
e1-2 (SFD-) - Body ground
Below 1 V
- for RHD:
Tester Connection
Specified Condition
f1-1 (SFD+) - Body ground
Below 1 V
f1-2 (SFD-) - Body ground
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
- Standard resistance:
- for LHD:
Tester Connection
Specified Condition
e1-1 (SFD+) - Ke1-1
Below 1 Ω
e1-2 (SFD-) - Ke1-2
Below 1 Ω
e1-1 (SFD+) - e1-2 (SFD-)
1 MΩ or higher
e1-1 (SFD+) - Body ground
1 MΩ or higher
e1-2 (SFD-) - Body ground
1 MΩ or higher
- for RHD:
Tester Connection
Specified Condition
f1-1 (SFD+) - Lf1-1
Below 1 Ω
f1-2 (SFD-) - Lf1-2
Below 1 Ω
f1-1 (SFD+) - f1-2 (SFD-)
1 MΩ or higher
f1-1 (SFD+) - Body ground
1 MΩ or higher
f1-2 (SFD-) - Body ground
1 MΩ or higher
|
|
||||
| OK | ||
| ||


