2005-2008 RAV4 · Service Manual RESTRAINTS

B1825/56 Short in Front Passenger Side - Side Squib Circuit

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The front passenger side - side squib circuit consists of the center airbag sensor and the front seat side airbag RH.
The circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front passenger side - side squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1825/56
The center airbag sensor receives a line short signal 5 times in the front passenger side - side squib circuit during primary check.
  1. No. 2 floor wire
  2. No. 2 seat airbag wire
  3. Front seat side airbag RH (Front passenger side - side squib) (for LHD)
  4. Front seat side airbag LH (Front passenger side - side squib) (for RHD)
  5. Center airbag sensor
B1826/56
Center airbag sensor receives an open signal in the front passenger side - side squib circuit for 2 seconds.
  1. No. 2 floor wire
  2. No. 2 seat airbag wire
  3. Front seat side airbag RH (Front passenger side - side squib) (for LHD)
  4. Front seat side airbag LH (Front passenger side - side squib) (for RHD)
  5. Center airbag sensor
B1827/56
Center airbag sensor receives a short to ground signal in the front passenger side - side squib circuit for 0.5 seconds.
  1. No. 2 floor wire
  2. No. 2 seat airbag wire
  3. Front seat side airbag RH (Front passenger side - side squib) (for LHD)
  4. Front seat side airbag LH (Front passenger side - side squib) (for RHD)
  5. Center airbag sensor
B1828/56
Center airbag sensor receives a short to B+ signal in the front passenger side - side squib circuit for 0.5 seconds.
  1. No. 2 floor wire
  2. No. 2 seat airbag wire
  3. Front seat side airbag RH (Front passenger side - side squib) (for LHD)
  4. Front seat side airbag LH (Front passenger side - side squib) (for RHD)
  5. Center airbag sensor

WIRING DIAGRAM

C128700E09

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK FRONT PASSENGER SIDE FRONT SEAT SIDE AIRBAG ASSEMBLY (FRONT PASSENGER SIDE - SIDE SQUIB)
C128705E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat side airbag RH.

  1. Connect the black wire side of SST to connector E.

    CAUTION:
    Never connect a tester to the front passenger side front seat side airbag (front passenger side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18060  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1825, B1826, B1827, B1828 or 56 is not output.

    HINT:
    DTCs other than DTC B1825, B1826, B1827, B1828 or 56 may be output at this time, but they are not related to this check.



OK
REPLACE FRONT PASSENGER SIDE FRONT SEAT SIDE AIRBAG ASSEMBLY
NG


2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. Check that the No. 2 seat airbag wire connectors (on the front passenger side - side squib) are not damaged.

    OK:
    Lock button is not disengaged, and claw of lock is not deformed or damaged.



NG
REPLACE FLOOR WIRE NO.2
OK


3. CHECK NO. 2 FLOOR WIRE (FRONT PASSENGER SIDE - SIDE SQUIB CIRCUIT)
C128706E01
  1. Disconnect the connector from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD:
    Tester Connection
    Specified Condition
    f1-1 (SFP+) - Body ground
    Below 1 V
    f1-2 (SFP-) - Body ground
    Below 1 V
    for RHD:
    Tester Connection
    Specified Condition
    e1-1 (SFP+) - Body ground
    Below 1 V
    e1-2 (SFP-) - Body ground
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    f1-1 (SFP+) - f1-2 (SFP-)
    Below 1 Ω
    f1-1 (SFP+) - Body ground
    1 MΩ or higher
    f1-2 (SFP-) - Body ground
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    e1-1 (SFP+) - e1-2 (SFP-)
    Below 1 Ω
    e1-1 (SFP+) - Body ground
    1 MΩ or higher
    e1-2 (SFP-) - Body ground
    1 MΩ or higher

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    f1-1 (SFP+) - f1-2 (SFP-)
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    e1-1 (SFP+) - e1-2 (SFP-)
    1 MΩ or higher



OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
NG


4. CHECK NO. 2 SEAT AIRBAG WIRE

  1. C131085E01
    Disconnect the No. 2 seat airbag wire connector from the No. 2 floor wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD:
    Tester Connection
    Specified Condition
    f1-1 (SFP+) - Body ground
    Below 1 V
    f1-2 (SFP-) - Body ground
    Below 1 V
    for RHD:
    Tester Connection
    Specified Condition
    e1-1 (SFP+) - Body ground
    Below 1 V
    e1-2 (SFP-) - Body ground
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    f1-1 (SFP+) - Lf1-1
    Below 1 Ω
    f1-2 (SFP-) - Lf1-2
    Below 1 Ω
    f1-1 (SFP+) - f1-2 (SFP-)
    1 MΩ or higher
    f1-1 (SFP+) - Body ground
    1 MΩ or higher
    f1-2 (SFP-) - Body ground
    1 MΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    e1-1 (SFP+) - Ke1-1
    Below 1 Ω
    e1-2 (SFP-) - Ke1-2
    Below 1 Ω
    e1-1 (SFP+) - e1-2 (SFP-)
    1 MΩ or higher
    e1-1 (SFP+) - Body ground
    1 MΩ or higher
    e1-2 (SFP-) - Body ground
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 2 SEAT AIRBAG WIRE
OK

REPAIR OR REPLACE NO. 2 FLOOR WIRE


← B1825/56 Short in Front Passenger Side - Side Squib Circuit (+ B1826/56, B1827/56, B1828/56) (Nov 2005 – Dec 2006)B1825/56 Short in Front Passenger Side - Side Squib Circuit (+ B1826/56, B1827/56, B1828/56) (from Aug 2007) →